MTD 616 Throttle Control Lever, Choke Control, Brake Pedal, Ignition Switch Module, Drive Pedal

Page 13

Throttle Control Lever

The throttle control lever is located on the right side of the tractor’s dash panel. This lever controls the speed of the engine and, on some models, when pushed all the way forward, the choke control also. When set in a given position, the throttle will maintain a uniform engine speed. See Figure 4-1.

IMPORTANT: When operating the tractor with the cutting deck engaged, be certain that the throttle lever is always in the FAST (rabbit) position.

Choke Control

On some models, moving the throttle lever all the way forward activates the engine’s choke

&AST

#HOKE

0OSITION

0OSITION

&AST

0OSITION

3LOW

 

3LOW

 

0OSITION

 

0OSITION

4

Operating

Your Lawn

Tractor

control. On all other models, the choke control can be found on the left side of the dash panel and is activated by pulling the knob outward. Activating the choke control closes the choke

plate on the carburetor and aids in starting the engine. Refer to Starting The Engine in this section of the manual for detailed starting instructions.

Brake Pedal

Figure 4-2

3TOP

0OSITION

.ORMAL

-OWING -ODE

3TART

0OSITION

WARNING

Never leave a running machine unattended. Always disengage

The brake pedal is located on the right front side of the tractor above the drive pedal along the running board. The brake pedal can be used for sudden stops or setting the parking brake.

NOTE: The brake pedal must be fully depressed to activate

the safety interlock switch when starting the tractor.

Ignition Switch Module

WARNING: Never leave a running machine unattended. Always disengage PTO, move shift lever into neutral position, set parking brake, stop engine and remove key to prevent unintended start- ing.

To start the engine, insert the key into the ignition switch and turn clockwise to the START position. Release the key into the NORMAL MOWING MODE position once the engine has fired.

To stop the engine, turn the ignition key counterclockwise to the STOP position. See Figure 4-3.

Figure 4-3

IMPORTANT: Prior to operating the tractor, refer to both Safety Interlock Switches and Starting The Engine in this section of the manual for detailed instructions regarding the Ignition Switch Module and operating the tractor in REVERSE CAUTION MODE.

Drive Pedal

The drive pedal is located below the brake pedal on the right front side of the tractor along the running board.

Depress the drive pedal with your right

foot when the tractor shift lever is in either FORWARD or REVERSE to cause

the tractor to move. Ground speed is

also controlled with the drive pedal. The further down the pedal is depressed, the

faster the tractor will travel. The pedal will return to its original position when it’s not depressed.

IMPORTANT: Always set the parking brake when leaving the tractor unattended.

PTO, move shift lever into neutral position, set parking brake, stop engine and remove key to prevent unintended starting.

IMPORTANT: Prior to operating the tractor, refer to both Safety Interlock Switches and Starting The Engine in this section of the manual for detailed instructions regarding the Ignition Switch Module and operating the tractor in REVERSE CAU-

TION MODE.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents OPERATOR’S Manual Table of Contents Slope Gauge Replace gasoline cap and tighten securely Use only an approved gasoline containerGeneral Operation Never allow children or others in or on towed equip- ment This manual and on the machine Slope OperationService Attaching the Battery Cables Setting Up Your Lawn TractorGas and Oil Fill-up Remove the hex bolt and wing nut from the negative cableAttaching The Steering Wheel Shipping Brace RemovalQuick Adjustment Seat Standard Adjustment SeatKnob Adjustment Seat Attaching The SeatIf so equipped Identifying the Mulch PlugBrake Pedal Operating Your Lawn TractorThrottle Control Lever Ignition Switch ModuleChoke Control Brake PedalSeat Adjustment Lever If Equipped Systems Indicator Monitor If EquippedElectric PTO Blade Engage PTO Blade Engage LeverReverse Caution Mode Safety Interlock SwitchesDeck Lift Lever Parking Brake ButtonEngaging the Parking Brake Setting the Cutting HeightStarting the Engine Driving The Tractor Stopping the EngineDriving On Slopes Drive PedalUsing the Deck Lift Lever Setting The Cruise ControlMoving the Tractor Manually Engaging the BladesHeadlights MowingMulching If Equipped Leveling the Deck Adjusting Your Lawn TractorFront To Rear Side to SideSeat Adjustment Parking Brake AdjustmentSteering Adjustment Quick Adjust Seat If so equippedMaintaining Your Lawn Tractor Cleaning the Engine And DeckKohler Single Shown EngineDeck Wash System If equipped Cutting Deck RemovalMove the tractor’s PTO Blade Engage into the OFF position Repeat steps 4-11 on the opposite side of the cutting deckTires BatteryFuses Cutting BladesChanging the Transmission Drive Belt Changing the Deck BeltChanging the Lower Deck Belt 46 Decks Belt Cover For an extended period Storing your tractor Rear Wheel Weight KitInch Two-stage Snow Thrower Inch Deck Mulch KitYour Responsibility Clean pre-cleaner, if so equipped Spark plug wires looseHousing Wide Dirty air cleaner06.18.06 Warranty734-1731 Drive Belt Transmission

616 specifications

The MTD 616 is a versatile and powerful ride-on mower that stands out in the landscaping equipment market due to its robust design and innovative technologies. This machine is particularly well-suited for residential and light commercial users, offering an exceptional combination of performance, comfort, and efficiency.

One of the main features of the MTD 616 is its durable build quality. A strong steel frame ensures the mower can withstand demanding conditions, while a wide cutting deck allows for efficient mowing of larger areas. The mower typically features a 42-inch deck, which strikes a perfect balance between cutting width and maneuverability, making it ideal for both open lawns and more confined spaces.

The MTD 616 is powered by a reliable engine, usually a gas-powered unit, providing sufficient torque and power to handle various grass types and terrains. This ensures that users can tackle thick grass and uneven ground without issues. The mower's transmission system is designed for smooth operation, often featuring an automatic or hydrostatic transmission that enables seamless speed adjustments while mowing.

In terms of user comfort, the MTD 616 is equipped with an ergonomic seat and intuitive controls, making it easy for operators to navigate and operate the mower efficiently. The machine's adjustable cutting height allows users to customize their mowing experience, accommodating different grass lengths and varying seasonal growth patterns.

Additionally, the MTD 616 highlights advanced technologies aimed at enhancing functionality. Some models incorporate a mulching feature, which helps in returning cut grass to the lawn as nutrient-rich mulch, promoting healthier growth. Other models may offer bagging options for easy collection of clippings, keeping the lawn tidy.

Safety is an important consideration, and the MTD 616 typically includes features such as a blade brake that stops the mower blades when the operator leaves the seat, ensuring greater safety during operation. Furthermore, its compact design and tight turning radius enhance maneuverability, making it suitable for navigating around landscaping features and garden beds.

Overall, the MTD 616 stands out as a formidable choice for users seeking a reliable and efficient ride-on mower. Its combination of robust construction, advanced features, and user-friendly design positions it as an excellent investment for maintaining a beautiful and well-manicured lawn. Whether it’s for homeowners or light commercial use, the MTD 616 offers the performance and versatility needed for effective grass management.
Top Page Image Contents