MTD 616 warranty Cutting Blades, Fuses

Page 25

Cutting Blades

WARNING: Be sure to shut the engine off, remove ignition key, disconnect the spark plug wire(s) and ground against the engine to prevent unintended starting before removing the cutting blade(s) for sharpening or replacement. Protect your hands by using heavy gloves or a rag to grasp the cutting blade.

WARNING: Periodically inspect the blade spindles for cracks or damage, especially if you strike a foreign object. Replace immedi- ately if damaged.

The blades may be removed as follows:

1.Remove the deck from beneath the tractor, (refer to Cutting Deck Removal) then gently flip the deck over to expose its underside.

2.Place a block of wood between the center deck hous- ing baffle and the cutting blade to act as a stabilizer. See Figure 6-5.

3.Use a 15/16” wrench to remove the hex flange nut that secures the blade to the spindle assembly. See Figure 6-5.

4.To properly sharpen the cutting blades, remove equal amounts of metal from both ends of the blades along the cutting edges, parallel to the trailing edge, at a 25° to 30° angle.

IMPORTANT: If the cutting edge of the blade has already been sharpened to within 1-5/8” from the edge, or if any metal separation is present, replace the blades with new ones. See Figure 6-6.

•It is important that each cutting blade edge be ground equally to maintain proper blade balance.

•When replacing the blade, be sure to install the blade with the side of the blade marked ‘‘Bottom’’ (or with a part number stamped in it) facing the ground when the mower is in the operating position.

IMPORTANT: Use a torque wrench to tighten the blade spindle hex flange nut to between 70 foot-pounds and 90 foot-pounds.

Figure 6-5

INCH

Figure 6-6

Fuses

•A fuse is installed in your tractor’s wiring harness to protect the tractor’s electrical system from damage caused by excessive amperage.

•If the electrical system does not function, or your tractor’s engine will not crank, first check to be certain that the fuse has not blown.

•It can either be found under the hood mounted behind the top of the dash panel on the support bar, or under the seat mounted to the inside of the tractor frame next to the battery tray.

WARNING: Always use a fuse with the same amperage capacity for replacement.

6

Maintaining

Your Lawn

Tractor

WARNING

Be sure to shut the engine off, remove ig- nition key, disconnect the spark plug wire(s) and ground against the engine to prevent unintended starting before removing

the cutting blade(s) for sharpening or replacement. Protect your hands by using heavy gloves or a rag to grasp the cutting blade.

Periodically inspect the blade spindles for cracks or damage, especially if you strike a foreign object. Replace immediately if damaged.

Always use a fuse with the same amperage capacity for replace- ment.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents OPERATOR’S Manual Table of Contents Slope Gauge Replace gasoline cap and tighten securely Use only an approved gasoline containerGeneral Operation Never allow children or others in or on towed equip- ment This manual and on the machine Slope OperationService Attaching the Battery Cables Setting Up Your Lawn TractorGas and Oil Fill-up Remove the hex bolt and wing nut from the negative cableAttaching The Steering Wheel Shipping Brace RemovalQuick Adjustment Seat Standard Adjustment SeatKnob Adjustment Seat Attaching The SeatIf so equipped Identifying the Mulch PlugBrake Pedal Operating Your Lawn TractorThrottle Control Lever Ignition Switch ModuleChoke Control Brake PedalSeat Adjustment Lever If Equipped Systems Indicator Monitor If EquippedElectric PTO Blade Engage PTO Blade Engage LeverReverse Caution Mode Safety Interlock SwitchesDeck Lift Lever Parking Brake ButtonEngaging the Parking Brake Setting the Cutting HeightStarting the Engine Driving The Tractor Stopping the EngineDriving On Slopes Drive PedalUsing the Deck Lift Lever Setting The Cruise ControlMoving the Tractor Manually Engaging the BladesHeadlights MowingMulching If Equipped Leveling the Deck Adjusting Your Lawn TractorFront To Rear Side to SideSeat Adjustment Parking Brake AdjustmentSteering Adjustment Quick Adjust Seat If so equippedMaintaining Your Lawn Tractor Cleaning the Engine And DeckKohler Single Shown EngineDeck Wash System If equipped Cutting Deck RemovalMove the tractor’s PTO Blade Engage into the OFF position Repeat steps 4-11 on the opposite side of the cutting deckTires BatteryFuses Cutting BladesChanging the Transmission Drive Belt Changing the Deck BeltChanging the Lower Deck Belt 46 Decks Belt Cover For an extended period Storing your tractor Rear Wheel Weight KitInch Two-stage Snow Thrower Inch Deck Mulch KitYour Responsibility Clean pre-cleaner, if so equipped Spark plug wires looseHousing Wide Dirty air cleaner06.18.06 Warranty734-1731 Drive Belt Transmission

616 specifications

The MTD 616 is a versatile and powerful ride-on mower that stands out in the landscaping equipment market due to its robust design and innovative technologies. This machine is particularly well-suited for residential and light commercial users, offering an exceptional combination of performance, comfort, and efficiency.

One of the main features of the MTD 616 is its durable build quality. A strong steel frame ensures the mower can withstand demanding conditions, while a wide cutting deck allows for efficient mowing of larger areas. The mower typically features a 42-inch deck, which strikes a perfect balance between cutting width and maneuverability, making it ideal for both open lawns and more confined spaces.

The MTD 616 is powered by a reliable engine, usually a gas-powered unit, providing sufficient torque and power to handle various grass types and terrains. This ensures that users can tackle thick grass and uneven ground without issues. The mower's transmission system is designed for smooth operation, often featuring an automatic or hydrostatic transmission that enables seamless speed adjustments while mowing.

In terms of user comfort, the MTD 616 is equipped with an ergonomic seat and intuitive controls, making it easy for operators to navigate and operate the mower efficiently. The machine's adjustable cutting height allows users to customize their mowing experience, accommodating different grass lengths and varying seasonal growth patterns.

Additionally, the MTD 616 highlights advanced technologies aimed at enhancing functionality. Some models incorporate a mulching feature, which helps in returning cut grass to the lawn as nutrient-rich mulch, promoting healthier growth. Other models may offer bagging options for easy collection of clippings, keeping the lawn tidy.

Safety is an important consideration, and the MTD 616 typically includes features such as a blade brake that stops the mower blades when the operator leaves the seat, ensuring greater safety during operation. Furthermore, its compact design and tight turning radius enhance maneuverability, making it suitable for navigating around landscaping features and garden beds.

Overall, the MTD 616 stands out as a formidable choice for users seeking a reliable and efficient ride-on mower. Its combination of robust construction, advanced features, and user-friendly design positions it as an excellent investment for maintaining a beautiful and well-manicured lawn. Whether it’s for homeowners or light commercial use, the MTD 616 offers the performance and versatility needed for effective grass management.
Top Page Image Contents