Marantz SR8400 manual This remote control is capable of learning, You already own

Page 37

ENGLISH

LEARN MODE

 

Programming the (PLAY) and Other Control

 

Buttons and Numeric Buttons

 

This remote control is capable of learning and

 

storing codes used by other remote controls that

 

you already own.

 

For codes which are not learned, the remote

 

control will transmit either the Marantz preset

 

codes from the initial settings, or remote codes

 

from another manufacturer’s AV equipment which

 

is set by the customer.

 

The receiver sensor for the remote control signals is

 

located at the top of the remote control.

This example shows how to learn the codes from the remote control of a DVD player.

1

 

 

 

2

 

4

 

 

 

 

 

 

LEARN

 

 

LEARN

 

 

 

USEPAGE 1

 

 

1

2

 

1

2

 

 

 

 

 

 

 

 

 

6

(When OK)

(failed)

 

(codes are full)

 

 

 

 

 

 

 

 

 

 

 

LEARN

 

 

LEARN

 

 

 

 

 

 

PAGE 1

2

 

PAGE 1

2

 

1

2

 

 

 

 

 

 

 

 

 

 

 

1. Hold down the M button for three seconds or

more.

If ERROR is displayed on the LCD, some error has prevented the command from being learned. If this happens, repeat the procedure for steps 4 and 5.

In some rare cases, ERROR may be displayed repeatedly during the learning operation. In this case, the transmitting remote control may have special signal codes. These codes cannot be learned by this remote control.

7. Follow the same procedure to make the remote control learn the other buttons.

8. Repeat the procedure in steps 3 to 6 to have the remote control learn the signal codes from a TV, CD player, or other AV equipment.

•W h e n n o b u t t o n s a r e p r e s s e d f o r approximately one minute during the learning operation, the remote control automatically returns to USE mode.

•When programming the source buttons, switch to the source in step 3, and then press the source button again.

9.When you have finished programming the codes for each button, press the M button.

The USE indicator is displayed on the LCD, and the newly stored codes can be used.

•If FULL is displayed on the LCD, the memory cannot hold any more learned codes in LEARN mode.

If FULL is displayed no matter how many times you try the learning operation, the remote control cannot accept any more new codes until some of the previously learned codes are deleted from the memory. Delete some of the learned buttons from the sources.

Note:

Programming the Direct Buttons and Rewriting Names

This example shows how to program codes from other manufacturer products to the DVD MENU button (D1) and change the display to OSD.

6

7

 

8

LEARN

 

LEARN

LEARN

PAGE 1

2

PAGE 1 2

PAGE 1 2

1. Hold down the M button for three seconds or

more.

The menu is displayed.

2. Press the D2 (LEARN) direct button.

The LEARN setting (LEARN) indicator is displayed. The LEARN indicator then blinks.

3. Press the DVD source button.

The first page of the direct button screen is displayed. There are four available pages. Pressing the > buttons cycles through the pages in this order 1 → 2 → 3 → 4 → 1.

4. Press the D1 (MENU) direct button.

The LEARN indicator blinks, and then displays to indicate that learning is ready.

5. Place the receiver sensor of the remote control (top) so that it is facing the transmitter of the DVD remote control (top) at a distance of about 5 cm (2 inches).

6. Press and hold down the OSD button of the transmitting DVD remote control, and check that OK is displayed on the LCD.

•To change MENU to OSD, press the 5 numeric button.

Each time the button is pressed, the display cycles through M → N → O → 5 → M.

8.After rewriting of the text is completed, press the OK cursor button.

To delete text that is already entered, press the 0 button to insert a space.

•In this example, MENU is changed to “OSD (space) (space)” in this step, and then OSD is displayed in the right side by pressing the OK button.

For details, refer to the section “Rewriting Names”.

9. In the same way, use the > button to select the page, and then press the direct button to program the codes.

10. After programming the codes for each of the buttons, press the M button.

The USE indicator displays on the LCD, and the newly stored codes can be transmitted.

REWRITING NAMES

This remote control allows the rewriting of names for the sources and direct buttons. This operation is performed for each individual source.

This example shows how to change the source name from DVD to AVD and AUDIO to SOUND.

3

4

5

The menu is displayed.

2. Press the D2 (LEARN) direct button.

The LEARN setting (LEARN) is displayed. The LEARN indicator then blinks.

3. Press the DVD source button.

4. Press the(PLAY) button.

The LEARN indicator blinks, and then displays to indicate that learning is ready.

5. Place the receiver sensor of the remote control (top) so that it is facing the transmitter of the DVD remote control (top) at a distance of about 5 cm (2 inches).

•To learn the remote control code, a button of the transmitting remote control should be pressed and held down until the “OK” is displayed on the LCD of the RC1400.

The holding time needs for 5 seconds or more. This time is depend on the remote control code.

The M button and > button cannot be taught. Only each one code can be learned for the LIGHT buttons 1 and 2, regardless of the source.

The remote control has finished learning when OK is displayed on the LCD.

If ERROR is displayed on the LCD, some error has prevented the command from being learned. If this happens, repeat the procedure for steps 4 and 5.

• After learning is completed, the remote

control automatically switches to name

rewriting mode. The left end “ ” indicator

on the MENU blinks to indicate that the

blinking part can be rewritten.

• If no names will be rewritten, press the OK

cursor button. The display returns to

learning standby mode by pressing the OK

NAME

PAGE 1 2

7

NAME

PAGE 1 2

NAME

PAGE 1 2

8

NAME

PAGE 1 2

NAME

PAGE 1 2

9

NAME

PAGE 1 2

6. Press and hold down the(PLAY) button of the transmitting DVD remote control, and check that OK is displayed on the LCD.

The remote control has finished learning when OK is displayed on the LCD.

cursor button.

 

7. To change the name, press the numeric

buttonsto enter the text.

 

• Use the cursor buttons

to move to the

sections to be rewritten on the LCD.

1. Hold down the M button for three seconds or more.

The menu is displayed.

34

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Model SR8400 User Guide Outlet before cleaning. Do not use liquid Cleaning Unplug this product from the wallCleaners or aerosol cleaners. Use a damp Cloth for cleaningProduct during a lightning storm, or when it is Power-Cord Protection Power-supply cordsLightning and power-line surges Power Lines An outside antenna systemPrecautions Table of Contents IntroductionAbout Dolby Pro Logic DescriptionAccessories FeaturesRemote Controller RC1400 Input Function Selector Front PanelPCM FL DisplaySBR, C Rear PanelNames and Functions When AMP mode is selectedAudio IN/OUT CD, TAPE, CD-R, TV, DVD, VCR1, DSS/VCR2 Digital Input Dig.1 6 / Output coaxial, opticalLCD Indicators Battery Replacement Interval Remote Control RangeSafety Precautions for Batteries Loading BatteriesGeneral Information of RC1400 Setting the TimeConnecting Speakers Speaker PlacementConnections Banana plug connections are also possible Connecting Audio ComponentsTighten the knob by turning clockwise and then Insert the banana plugThere are 3 types of video jacks on the rear panel Connecting Video ComponentsVideo jack Component jackConnecting Multi Channel Audio Source Connecting the Remote Control JacksConnecting AN External Power Amplifier Connecting the supplied AM loop antenna Connecting the Antenna TerminalsPlace the antenna on stable surface Multiroom Connecting for the Multi RoomOn Screen Display Menu System SetupLarge Speaker SetupSmall YESPreference PL II PRO Logic II Music Parameter SurroundCS II Circle Surround Parameter Multi RoomCH Input Level DC Trigger SetupAdjusting the Tone Bass Treble Control Selecting the Surround ModeBasic Operation Video ConvertUsing the Sleep Timer Surround ModeTemporarily Turning OFF Sound Dolby DigitalDTS-ES Discrete 6.1, Matrix This mode bypasses all surround processingDts, Neo6 Cinema, Neo6 Music Neo6 Cinema, Neo6 MusicSBL Other Function Speaker A/B Recording AN Analog SourceHT-EQ CH Input AUX2 InputUsing the SR8400 Using the remote control unit Preset MemoryBasic Operation Tuner Listening to the Tuner← Down Multi Room Playback Using Multi Room Playback Using Multi Speaker TerminalsMulti Room SystemControlling a Marantz VCR VCR Mode Remote Controller OperationControlling Marantz Components Turns the CD recorder on and off Basic Operation When operating non-Marantz AV equipment productsNormal operation status Press the buttons to operate the DVDStoring codes used by other remote controls that This remote control is capable of learningControl will transmit either the Marantz preset Codes from the initial settings, or remote codesErasing direct buttons Erasing buttonsProgramming Macros Press the 5 numeric button to select M Press the D3 Name direct buttonPress Cursor button to next Repeat steps 6 and 7, and then enter V, I, EReceiving remote control Clone ModeTransmitting remote control Setting the Lighting Time SetupSetting the Macro Interval Time Adjusting the Display ContrastSymptom Cause Remedy TroubleshootingGeneral Malfunction Memory backupTechnical Specifications Dimensions Source button name AMP Setup CodesSource button name AMP, Tuner Source button name AUX2 Source button name TapeSource button name CD, CDR, MD Source button name TVIii Source button name TV Source button name VCR VCRSTS Source button name DVDSource button name Tuner FunctionsSource button name CD Source button name CDR06BW851250 Japan
Top Page Image Contents