ENGLISH | SETTING THE MACRO TIMER |
| ||
Setting the macro timer enables the macro | ||||
| ||||
| program to automatically turn the power for a | |||
| device on or off or perform other operations. | |||
| In the settings, you can select to execute the | |||
| macro timer everyday or only once. | |||
| Be sure to set the clock to the correct time before | |||
| using the timer. The macro timer can only be set | |||
| for one program a day. |
| ||
| This example shows how to use the timer only | |||
| once at 20:35 to execute a macro programmed to | |||
|
|
| ||
| 2 | 3 | 4 | |
EXECUTING THE MACRO TIMER
The macro program starts when the time that was
set is reached. The TIMER 
indicator lights up whenever the macro timer is activated.
Note:
To execute the macro timer, place the remote control facing the infrared sensor of the device to be operated. If the remote control is not in a suitable position, it may not operate the device properly.
CLONE MODE
CREATING COPIES USING CLONE MODE
1. Place the receiver sensor of the receiving remote control (top) so that it is facing the transmitter of the transmitting remote control (top) at a distance of about 5 cm (2 inches).
2. Hold down the M button of the transmitting remote control for three seconds or more.
The menu is displayed.
3. Press the > button to display the fourth page
4. Press the D3 (TX) direct button .
5. Hold down the M button of the receiving remote control for three seconds or more.
The menu is displayed.
6. Press the > button to display the fourth page
COPYING BY SOURCE
The 12 sources can be copied on a source by source basis. You can select from up to 12 source types.
<Receiving remote control>
6 | 7 | 8 |
| LEARN |
|
PAGE 1 2 3 4 | 1 2 3 4 | PAGE 1 2 3 4 |
1. Place the receiver sensor of the receiving
USEPAGE 1 2 3
5
LEARN
MACRO
PAGE 1 2 3
LEARN
MACRO
PAGE 1 2
6
LEARN
MACRO
PAGE 1 2 3
LEARN
MACRO
1 2 3
All of the codes programmed to the RC1400 remote control can be copied to another RC1400 using a few simple operations.
•The remote control can copy the entire contents or the contents for specific source buttons.
• W h e n c o p y i n g t h e e n t i r e c o n t e n t s , a l l p r o g r a m m e d c o d e s , m o d i f i e d n a m e s , programmed macros, and signal transmission intervals are copied.
When copying the contents for source buttons, the programmed codes and modified names are copied.
7. Press the D1 (RX) direct button .
8. Press the OK cursor button on the receiving
remote control.
9. P r e s s t h e OK c u r s o r b u t t o n o n t h e transmitting remote control.
When copying is started, the bar indicators on both LCDs start to move from the left to the right.
• When the copying operation is completed, |
TX OK is displayed on the LCD of the |
transmitting remote control, and RX OK is |
remote control (top) so that it is facing the transmitter of the transmitting remote control (top) at a distance of about 5 cm (2 inches).
2. Hold down the M button of the transmitting remote control for three seconds or more.
The menu is displayed.
3. Press the > button to display the fourth page CLONE menu.
4. Press the D3 (TX) direct button .
The transmitting side is now ready.
5. Hold down the M button of the receiving remote control for three seconds or more.
1. Hold down the M button for three seconds or more.
The menu is displayed.
2. Press the > button to display the third page TIMER menu.
3. Press the D2 (ONCE?) direct button .
The
• To cancel timer operation, press CANCEL.
4.Press the D1 (M-01) direct button .
The time which is set previously is displayed.
5.Press the 2 and 0 numeric button to set the hour indicator to 20.
6.Press the 3 and 5 numeric button to set the minute indicator to 35.
7.Press the OK cursor button .
This finalizes the time.
8.To exit, press the M button .
To cancel the macro timer, return to the TIMER menu and press the D5 (CANCEL) and then press D1
Note:
The clone function can only be used for copying when using the same model (RC1400) for both the transmitting and receiving remote control.
COPYING ENTIRE CONTENTS
<Transmitting remote control>
3 | 4 | 9 |
PAGE 1 2 3 4 | PAGE 1 2 3 4 | PAGE 1 2 3 4 |
<Receiving remote control> |
| |
5 | 6 | 9 |
PAGE 1 2 3 4 | PAGE 1 2 3 4 | 1 2 3 4 |
| displayed on the LCD of the receiving |
| remote control. |
• Do not touch either of the remote controls | |
| during the copying operation. Doing so |
| could cause copying to fail. |
• | If the copying fails in the middle of the |
| copying process, RX ERROR is displayed |
| on the receiving remote control. Check |
| and perform steps 1 to 7 again. |
• | Copying takes about three minutes to |
| complete when the transmitting remote |
| control has been programmed to 100% |
| capacity. |
10. Once copying is completed, press the M | |
button on both remote controls. | |
6. Press the > button to display the fourth page CLONE menu.
7. Press the D2
8. Press the source button to be copied.
The receiving side is now ready.
The name of the source which was pressed is displayed on the LCD.
•Each time the source button is pressed, the name is displayed on the LCD.
9.Press the OK cursor button on the receiving remote control.
10. P r e s s t h e OK c u r s o r b u t t o n o n t h e transmitting remote control.
When copying is started, the bar indicators on both LCDs start to move from the left to the right.
•When the copying operation is completed, TX OK is displayed on the LCD of the transmitting remote control, and RX OK is displayed on the LCD of the receiving remote control.
•Do not touch either of the remote controls during the copying operation. Doing so could cause copying to fail.
38