Marantz SR8400 manual Setup, Setting the Lighting Time, Setting the Macro Interval Time

Page 42

•If the copying fails in the middle of the copying process, ERROR is displayed on the remote control.

Check and perform steps 1 to 7 again.

11.Once copying is completed, press the M button on both remote controls.

SETUP

SETTING THE LIGHTING TIME

•The LCD lights up when the LIGHT buttons are pressed. The LCD remains lit while the pressed button is held down, and it goes off when the button is released.

•The LCD continues to light up if another button is pressed while it is lit or if pressed within two seconds after the light goes off.

•The lighting time can be set in one-second units from 0 to 60 seconds.

The LIGHT buttons have light - absorbing properties that enable them to store light. If the buttons are no longer illuminated in a dimly lit environment, bring the buttons near a fluorescent lamp or other light source for a sufficient amount of time. This should illuminate the buttons again.

•The LIGHT buttons consist of a LIGHT1 and LIGHT2 button, and they both perform the same operation.

The factory default lighting time is set to 15 seconds.

This example shows how to set the lighting time to 20 seconds.

2

3

 

 

 

 

4

 

 

 

 

LEARN

 

 

 

 

LEARN

 

 

 

PAGE 1

2

1

2

3

4

1

2

3

4

1. Hold down the M button for three seconds or more.

The menu is displayed.

2. Press the > button to display the second page SETUP menu.

3. Press the D1 (LIGHT) direct button .

The LIGHT is displayed on the LCD

4. Press the or cursor button to set the lighting time.

5. Press the OK cursor button to enter the lighting time.

6. Once the setting is finished, press the M button .

SETTING THE MACRO INTERVAL TIME

When a macro program is executed, control signals are transmitted in sequence . This transmission interval (interval time) can be set in 0.5-seconds units from 0.5 to 5 seconds.

If the interval time is set in this Setup mode, the interval times for all programmed macros are changed. If necessary, use EDIT (see page 37) in the macro program to change the individual transmission times.

The factory default setting for the transmission interval is 1 second.

This example shows how to set the interval time to 5 seconds.

2

3

 

 

 

 

4

 

 

 

 

LEARN

 

 

 

 

LEARN

 

 

 

PAGE 1

2

1

2

3

4

1

2

3

4

1. Hold down the M button for three seconds or more.

The menu is displayed.

2. Press the > button to display the second page SETUP menu.

3. Press the D2 (I-TIME) direct button .

4. Press the or cursor button to set the interval time.

Holding down the cursor button fast-forwards the time indicator.

5. Press the OK cursor button to enter the interval time.

6. Once the setting is finished, press the M button .

ADJUSTING THE DISPLAY CONTRAST

The contrast of the LCD can be adjusted. Adjust for maximum visibility according to your viewing environment.

2

3

 

 

 

 

4

 

 

 

 

LEARN

 

 

 

 

LEARN

 

 

 

PAGE 1

2

1

2

3

4

1

2

3

4

1. Hold down the M button for three seconds or more.

The menu is displayed.

2. Press the > button to display the second page SETUP menu.

3.Press the D3 (CONT) direct button .

4.Press the or cursor button and set the display contrast for maximum visibility.

The adjustment has 10 levels.

The factory default setting for the contrast is the fifth level.

5.Press the OK cursor button to enter the display contrast.

6.Once the setting is finished, press the M button .

ENGLISH

39

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Model SR8400 User Guide Cleaners or aerosol cleaners. Use a damp Cleaning Unplug this product from the wallOutlet before cleaning. Do not use liquid Cloth for cleaningLightning and power-line surges Power-Cord Protection Power-supply cordsProduct during a lightning storm, or when it is Power Lines An outside antenna systemTable of Contents Introduction PrecautionsDescription About Dolby Pro LogicFeatures AccessoriesRemote Controller RC1400 Front Panel Input Function SelectorFL Display PCMRear Panel SBR, CAudio IN/OUT CD, TAPE, CD-R, TV, DVD, VCR1, DSS/VCR2 When AMP mode is selectedNames and Functions Digital Input Dig.1 6 / Output coaxial, opticalLCD Indicators Safety Precautions for Batteries Remote Control RangeBattery Replacement Interval Loading BatteriesSetting the Time General Information of RC1400Speaker Placement Connecting SpeakersConnections Tighten the knob by turning clockwise and then Connecting Audio ComponentsBanana plug connections are also possible Insert the banana plugVideo jack Connecting Video ComponentsThere are 3 types of video jacks on the rear panel Component jackConnecting the Remote Control Jacks Connecting Multi Channel Audio SourceConnecting AN External Power Amplifier Connecting the Antenna Terminals Connecting the supplied AM loop antennaPlace the antenna on stable surface Connecting for the Multi Room MultiroomSetup On Screen Display Menu SystemSmall Speaker SetupLarge YESPreference CS II Circle Surround Parameter SurroundPL II PRO Logic II Music Parameter Multi RoomDC Trigger Setup CH Input LevelBasic Operation Selecting the Surround ModeAdjusting the Tone Bass Treble Control Video ConvertTemporarily Turning OFF Sound Surround ModeUsing the Sleep Timer Dolby DigitalDts, Neo6 Cinema, Neo6 Music This mode bypasses all surround processingDTS-ES Discrete 6.1, Matrix Neo6 Cinema, Neo6 MusicSBL Other Function HT-EQ CH Input Recording AN Analog SourceSpeaker A/B AUX2 InputBasic Operation Tuner Preset MemoryUsing the SR8400 Using the remote control unit Listening to the Tuner← Down Multi Room Multi Room Playback Using Multi Speaker TerminalsMulti Room Playback Using SystemRemote Controller Operation Controlling a Marantz VCR VCR ModeControlling Marantz Components Turns the CD recorder on and off Normal operation status When operating non-Marantz AV equipment productsBasic Operation Press the buttons to operate the DVDControl will transmit either the Marantz preset This remote control is capable of learningStoring codes used by other remote controls that Codes from the initial settings, or remote codesErasing buttons Erasing direct buttonsProgramming Macros Press Cursor button to next Press the D3 Name direct buttonPress the 5 numeric button to select M Repeat steps 6 and 7, and then enter V, I, EClone Mode Receiving remote controlTransmitting remote control Setting the Macro Interval Time SetupSetting the Lighting Time Adjusting the Display ContrastTroubleshooting Symptom Cause RemedyMemory backup General MalfunctionTechnical Specifications Dimensions Setup Codes Source button name AMPSource button name AMP, Tuner Source button name CD, CDR, MD Source button name TapeSource button name AUX2 Source button name TVIii VCR Source button name TV Source button name VCRSource button name DVD STSSource button name CD FunctionsSource button name Tuner Source button name CDRJapan 06BW851250
Top Page Image Contents