Multiquip GBWE Balloon Installation Gbw/Gbwe/Gbs, Setup, Installing the Balloon, Releasing Buckle

Page 20

BALLOON INSTALLATION (GBW/GBWE/GBS)

SETUP

BALLOON INSTALLATION (GBW/GBWE/GBS)

1.Insert the balloon assembly into the mast. Tighten the T-bolt securely. See Figure 15.

BALLOON

PROTECTIVE

COVER

T-BOLT

MAST

Figure 15. Installing the Balloon

2.Unsnap the three buttons on the bottom of the balloon cover and unzip the cover. See Figure 16

3.Remove the AC Power Cable from the inside pocket

of the balloon cover. See Figure 16.

AC POWER

CABLE

ZIPPER

5.Connect the power cable to the lamp cable connector. See Figure 18.

LAMP CABLE

CONNECTOR

POWER CABLE

CONNECTOR

Figure 18. Connecting the Power Cable

6.Secure the power cable by hooking it to the eyelet on the bottom of the balloon as shown in Figure 19.

CABLE HOOK

BUTTON

Figure 16. Removal of AC Power Cable from

Balloon Cover

4.Fold the balloon cover into itself and zip it up. See Figure 17.

FOLD PROTECTIVE

COVER INTO ITSELF

ZIPPER

BALLOON

FULLY

EXPOSED

Figure 19. Securing Cable with Hook

7.Release the buckle on the belt holding the balloon together. See Figure 20.

BUCKLE

Figure 17. Folding Balloon Cover

Figure 20. Releasing Buckle

PAGE 20 — GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #0 (07/23/09)

Image 20

Contents OPERATION AND PARTS MANUAL THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMESGBS Offset Pole With Lamp GBP Lamp Only GBHM Hitch Mount Accessory GLOBUG SERIES MODELS GBW/GBWE Pentapod With LampPROPOSITION 65 WARNING TABLE OF CONTENTS Component DrawingsGBW/GBWE/GBS/GBP GBHM/GBMPPARTS ORDERING PROCEDURES When ordering parts, please supplyOrdering parts has never been easier Choose from three easy optionsSAFETY INFORMATION SAFETY MESSAGESSAFETY SYMBOLS DANGERﬁrst aid kit GENERAL SAFETYﬁre extinguisher LIGHTING SYSTEM SAFETY LAMP SAFETY NEVER attempt service on a running machine  ALWAYS make sure lamp surface is clean and dryBALLOON SAFETY GENERATOR SAFETYELECTRICAL SAFETY Power Cord/Cable SafetyCart Type - No Liﬁting Hook TRANSPORTING SAFETYLOADING AND UNLOADING Cart Type - With Liﬁting Hook SPECIFICATIONS Table 1. SpeciﬁcationsLamp BALLOONDIMENSIONS GBW/GBWE Table 2. GBW DimensionsDescription Figure 1. GBW/GBWE DimensionsDIMENSIONS GBS D E JBALLOON ASSEMBLY Figure 2. GBS DimensionsDIMENSIONS GBP Table 4. GBP DimensionsDimension inches mm Figure 3. GBP DimensionsFOOTCANDLE PLOT VALUES LISTED AS FOOTCANDLESSCALE 1 GRID = 50 FT. 15.24 METERS Figure 4. Illumination RangeGENERAL INFORMATION Table 5. Extension Cord Gauge SelectionVolts RatingCOMPONENTS GBW/GBWEGBMP GBHM6. Pentapod - Supports and holds up the GBW SETUP GBW/GBWE SETUPGBS SETUP BALLOON INSTALLATION GBW/GBWE/GBS Figure 15. Installing the BalloonFigure 18. Connecting the Power Cable Figure 16. Removal of AC Power Cable from Balloon CoverNUT AND GBHM INSTALLATIONFigure 21. GBHM Installation GBMP INSTALLATION Figure 22. GBMP InstallationOPERATION RAISING THE MAST GBW/GBWELOWERING THE MAST GBW/GBWE shock, electrocution and even deathSHUTDOWN APPLYING POWERSHUTTING DOWN LAMP ONLY STORAGE GBW/GBWE \ CAUTION MAINTENANCEREPLACING LAMP REPLACING BALLOON FILTER REPLACEMENT Table 6. Troubleshooting SYMPTOMPOSSIBLE PROBLEM SOLUTIONGBW/GBWE E2 GBSB2 B1 B2 P3 E2 P1CHECK ITEM Table 7. Periodic Check and MaintenancePART 1000 WATT METAL HALIDE LAMP WIRING DIAGRAMCONNECTOR FEMALE CONNECTOR MALE Page SAMPLE PARTS LIST EXPLANATION OF CODE IN REMARKS COLUMNNO. Column PART NO. ColumnSUGGESTED SPARE PARTS GBW/GBWE/GBS/GBP LIGHTING SYSTEM 1 to 3 unitsNAMEPLATES AND DECALS GBW/GBWE GloBugTM Lighting SystemLamp OFF Push the button in the hole with a small MODELPART NAME REMARKSNAMEPLATES AND DECALS GBS GloBugTM Lighting SystemMODEL SERIAL NO A-0000000-00REMARKS BALLOON AND LAMP ASSY GBW/GBWE AND GBS OPTIONAL BALLOONS AND MESSAGE STRIPSBUTTON SCREW & WASHER M8x25 41$#1221 MAST ASSY GBW/GBWE1715 BOTTOM PLATE SECOND MAST PENTAPOD ASSY GBW/GBWE PENTAPOD ASSY GBW/GBWE POLE ASSY GBS CONTACT MQ UNIT SALES POLE MOUNT KITHITCH MOUNT ASSY GBHM HITCH MOUNT PLATE MOUNT ASSY GBMP MOUNTING PLATE TERMS AND CONDITIONS OF SALE - PARTS SPECIAL EXPEDITING SERVICEPAYMENT TERMS FREIGHT POLICYPage HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLINGWarranty Department Service Department