Multiquip GBP5000H GDP-5000H Load Application, Single Phase Load 60 Hz, Three Phase Load 180 Hz

Page 15

Single Phase Load — 60 Hz

Always be sure to check the nameplate on the generator and equipment to insure the wattage, amperage and frequency requirements are satisfactorily supplied by the generator for operating the equipment.

Generally, the wattage listed on the nameplate of the equipment is its rated output. Equipment may require 130— 150% more wattage than the rating on the nameplate, as the wattage is influenced by the efficiency, power factor and starting system of the equipment.

NOTE

If wattage is not given on the equipment's name plate, approximate wattage may be determined by multiplying nameplate voltage by the nameplate amperage.

WATTS = VOLTAGE x AMPERAGE

To determine the running wattage for your load, multiply the running wattage as indicated by steps 1, 2, and 3 below:

1.INCANDESCENT LOADS

Lights, heaters and similar appliances. Total the running wattage and multiply by 1. Example:

29 light bulbs @ 100W each = 2.9 KW use a 3 KW generator.

2.SMALL MOTORS

Drills and other small power tools.

Total the running wattage and multiply by 2. Example:

A 1 inch drill runs at 1 KW use a 2 KW generator.

3.LARGE MOTORS

Submersible pumps, table saws etc.

Total the running wattage and multiply by 3. Example:

A conveyor belt runs at 8 KW use a 24 KW generator.

GDP-5000H — LOAD APPLICATION

CAUTION:

Motors and motor-driven equipment draw much greater current for starting than during operation.

An inadequate size connecting cable which cannot carry

the required load can cause a voltage drop which can burn out the appliance or tool and overheat the cable.

The idle control is operated at minimum load capacity of 100W. If the load capacity is less than 100W, throw the idle control switch to the OFF position.

CAUTION:

Before connecting this generator to any building’s electrical system, a licensed electrician must install an isolation (transfer) switch. Serious injury or death may result without this transfer switch.

Three Phase Load — 180 Hz

180 cycle, three phase, 230V, motor-in-head vibrators can be operated with this generator. When operating more than one concrete vibrator, the ON/OFF switch of each concrete vibrators shall be turned on one at a time.

If they are switched on simultaneously, the circuit breaker may trip or the engine may be overloaded.

NOTE

If output (kVA) is not given on the vibrators nameplate, approximate output may be determined by multiplying voltage by amperage by .

GDP-5000H A.C. GENERATOR — OPERATION AND PARTS MANUAL — REV. #2 (07/23/08) — PAGE 15

Image 15
Contents Model GDP5000H Proposition 65WARNING Page Table of Contents Parts Ordering Procedures Best Deal! Order via Internet Dealers OnlyOrder via Fax Dealers Only Maintenance Safety Rules for Safe OperationEmergencies Machine Safety Decals Operation and Safety DecalsEffects of Altitude and Heat SpecificationsExcitation System GDP-5000H General InformationGenerator Control BoxGDP-5000H Controls and Indicators Indoor Installation Outdoor InstallationGDP-5000H PRE-SETUP Fuel Lubrication OilGDP-5000H Instrumentation Single Phase Load 60 Hz Three Phase Load 180 HzGDP-5000H Load Application GDP-5000H Load Application GDP-5000H Operating Instructions GDP-5000H Maintenance Generator Storage GDP-5000H Preparation for Long -TERM StorageGDP-5000H -WIRING Diagram Engine Troubleshooting Symptom Possible Problem Solution GDP-5000H -TROUBLESHOOTING EngineGDP-5000H -TROUBLESHOOTING Engine GDP-5000H -TROUBLESHOOTING Generator Voltage Output GDP-5000H -TROUBLESHOOTING GeneratorPage QTY. Column GDP-5000H Explanation of Code in Remarks ColumnNO. Column Part NO. ColumnQty Description GDP-5000H Spare Parts ListGDP-5000H ENGINE/GENERATOR Assy ENGINE, Honda Generator AssemblyMuffler Assembly Pipe Frame AssemblyGDP-5000H Generator Assy SET Bolt Rotor Includes Item WNot Sold Seperately BearingGDP-5000H Control BOX Assy Wire Harness Full Power SwitchOperation Switch Idle Control SwitchGDP-5000H Muffler Assy Tapping Screw MufflerProtector ArrestorGDP-5000H Pipe Frame Assy Stopper Pipe FrameBase Rubber SuspensionGDP-5000H Nameplate and Decals DCS01 NameplateModel & Serial Number Honda GX340K1 Engine Cylinder Head PACKING, Head Cover GUIDE, IN. Valve Over SizeCLIP, Valve Guide Cover COMP., HeadHonda GX340K1 Engine Recoil Starter SPRING, Friction Starter ASSY, RecoilPULLEY, Recoil Starter RATCHET, StarterHonda GX340K1 Engine FAN Cover Cover COMP., FAN ShroudClip Honda GX340K1 Engine CAMSHAFT/VALVES ARM, Valve Rocker SPRING, Weight ReturnNUT, Pivot Adjusting ROD, PushHonda GX340K1 Engine PISTON/RINGS PIN, Piston Ring SET, Piston STDRing SET, Piston Piston STDHonda GX340K1 Engine AIR Cleaner Tube Breather ELEMENT, AIR CleanerSTAY, AIR Cleaner SEAL, AIR CleanerHonda GX340K1 Engine Cylinder Barrel BOLT, Drain Plug Switch ASSY., OIL LevelBarrel ASSY., Cylinder SHAFT, Governor ARMCylinder Barrel ASSY. Electric Start 12000ZE3826 Honda GX340K1 Engine Crankcase COVER/GOVERNOR PACKING, Case Cover Honda GX340K1 Engine FLYWHEEL/FAN Assy NUT, SPECIAL, 16 MM FAN, CoolingPULLEY, Starter Flywheel CompHonda GX340K1 Engine Coil Assy Coil ASSY., Lamp 12V/25W CLAMP, WireCORD, Stop Switch Coil ASSY., IgnitionHonda GX340K1 Engine Crankshaft Assy WEIGHT, Balancer GEAR, Balancer DriveGEAR, Timing Honda GX340K1 Engine Electric Starter Assy BRAKET, Center WIRE, Water CoverContactor Assy Armature CompHonda GX340K1 Engine Governor Controls Assy BOLT, Governor ARM ARM, GovernorROD, Governor SPRING, GovernorHonda GX340K1 Engine Carburetor Assy Valve SET, Float PACKING, AIR CleanerCLIP, Wire Harness Gasket SETHonda GX340K1 Engine Solenoid Assy Solenoid Assy Honda GX340K1 Engine Fuel Cock Assy CUP, Fuel Strainer SCREEN, Fuel StrainerRing Filter CUPFreight Policy Terms and Conditions of Sale PartsPage HERE’S HOW to GET Help