Korg Electric Keyboard Limit-Cho/Fl, Limit-Phaser, 201, Limiter Chorus/Flanger, Limiter Phaser

71: Limit–Cho/Fl

(Limiter – Chorus/Flanger)

This effect combines a mono-type limiter and a chorus/ flanger. You can change the order of the effect connection.

Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left				Wet / Dry
	Routing
		Chorus/Flanger
	Limiter
+	Limiter	Chorus/Flanger		Normal
	EQ Trim LEQ HEQ		+
				Output Mode
	Gain Adjust
			–
		Feedback		Wet Invert
			Cho/Flng Wet / Dry
Right				Wet / Dry
	Envelope - Control	LFO: Tri / Sine

a	[LMT] Ratio		1.0:1...50.0:1, Inf:1
	Sets the signal compression ratio			☞ Fx:03
	Threshld (Threshold)			–40...0dB
b	Sets the level above which the compressor is applied			☞ Fx:03
	G.Adj (Gain Adjust)		–Inf, –38...+24dB
	Sets the limiter output gain			☞ Fx:03
	Attack			1...100
c	Sets the attack time			☞ Fx:03
	Release			1...100
	Sets the release time			☞ Fx:03
	[CH/FL] LFO (LFO Waveform)			Tri, Sine
d	Selects the LFO waveform of the chorus/flanger
	F (LFO Frequency)			0.02...20.00Hz
	Sets the LFO speed
	Dly (Delay Time)			0.0...50.0ms
	Sets the delay time
e	Dep (Depth)			0...100
	Sets the depth of LFO modulation
	Feedback			–100...+100
	Sets the feedback amount			☞ Fx:20
f	[F] EQ Trim			0...100
	Sets the EQ input level
	[F] Pre LEQ Gain [dB]			–15...+15dB
g	Sets the gain of Low EQ
	Pre HEQ Gain [dB]			–15...+15dB
	Sets the gain of High EQ
	[F] Cho/Flng W/D	–Wet...–2:98, Dry, 2:98...Wet
h	Sets the effect balance of the chorus/flanger			☞ Fx:10, 20
	Output Mode		Normal, Wet Inv
	Selects the output mode for the chorus/flanger			☞ Fx:67
	Routing	LMT→	CH/FL, CH/FL→ LMT

iSwitches the order of the limiter and chorus/flanger connection

☞Fx:67

	W/D (Wet/Dly)	Dry, 1:99...99:1, Wet
	Sets the balance between the effect and dry sounds
j	(Source)	Off...Tempo
	Selects the modulation source of the effect balance
	(Amount)	–100...+100
	Sets the modulation amount of the effect balance

72: Limit–Phaser

(Limiter – Phaser)

This effect combines a mono-type limiter and a phaser. You can change the order of the effect connection.

Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left				Wet / Dry
			Routing
	Limiter
			Phaser
+	Limiter		Phaser	Normal
	Gain Adjust		+
				Output Mode
			–
				Wet Invert
			Resonance
			Phaser Wet / Dry
Right				Wet / Dry
	Envelope - Control	LFO: Tri / Sine

a	[LMT] Ratio	1.0:1...50.0:1, Inf:1
	Sets the signal compression ratio		☞ Fx:03
	Threshld (Threshold)		–40...0dB
b	Sets the level above which the compressor is applied		☞ Fx:03
	G.Adj (Gain Adjust)	–Inf, –38...+24dB
	Sets the limiter output gain		☞ Fx:03
	Attack		1...100
c	Sets the attack time		☞ Fx:03
	Release		1...100
	Sets the release time		☞ Fx:03
	[PHS] LFO (LFO Waveform)		Tri, Sine
d	Selects the LFO waveform of the phaser
	F (LFO Frequency)	0.02...20.00Hz
	Sets the LFO speed
	Manu (Manual)		0...100
	Sets the frequency to which the effect is applied
e	Dep (Depth)		0...100
	Sets the depth of LFO modulation
	Resonance		–100...+100
	Sets the resonance amount		☞ Fx:23
	[P] Phaser W/D	–Wet...–2:98, Dry, 2:98...Wet
f	Sets the phaser effect balance		☞ Fx:10, 23
	Output Mode	Normal, Wet Inv
	Selects the phaser output mode		☞ Fx:67
g	Routing	LMT→ PHS, PHS→ LMT
	Switches the order of the limiter and phaser connection		☞ Fx:67
	W/D (Wet/Dly)	Dry, 1:99...99:1, Wet
	Sets the balance between the effect and dry sounds
h	(Source)		Off...Tempo
	Selects the modulation source of the effect balance
	(Amount)		–100...+100
	Sets the modulation amount of the effect balance

Effect

201