Korg Electric Keyboard manual 2b REC Setup, Mode Sample Mode, Mode REC Mode Manual, Auto

For example if the 16 Mbyte SIMM (sample data RAM) included with the EXB-SMPL option (sold separately) is installed in slot 1 and you install 32 Mbytes in slot 2, you will be able to select “Bank (RAM Bank)” 1 (16 Mbyte), 3 (16 Mbyte), and 4 (16 Mbyte). Each bank is a 16 Mbyte unit. (If you install a 32 Mbyte SIMM in slot 1 and slot 2, all banks can be selected, and the total capac- ity will be 64 Mbytes.)

Mode (Sample Mode) [L-Mono, R-Mono, Stereo]

Select s the channel(s) to be sampled, to specify whether a mono or a stereo sample will be recorded.

Depending on the “Input1, Input2” (1.1–3a) settings, the external source from the AUDIO INPUT 1 and 2 jacks will be sent, either as direct sound without being routed through an effect, or as effect-processed sound routed through an inser- tion effect, to the L/R bus and sampled from the internal L and R channels.

L-Mono:The sound of the internal L channel will be sam- pled in mono.

R-Mono:The sound of the internal R channel will be sam- pled in mono.

Stereo: The sound of the internal L and R channels will be sampled in stereo. When you sample in stereo, a stereo mul- tisample or sample will be created.

Example 1:

Sampling a monaural source connected to AUDIO INPUT 1 without applying internal effects

Input1 “Lvl (Level)”	(1.1–3a)	127
Input1 “Pan”	(1.1–3a)	L000
Input1 “BUS	(1.1–3a)	L/R
(BUS(IFX)Select)”
“Recording Level”	(1.1–2c, 1.1–3e)as appropriate
“Mode (Sample Mode)”	(1.1–2a)	L-Mono

Example 2:

A monaural source connected to AUDIO INPUT 1 routed through the internal insertion effect IFX 52: Rev Hall, and sampled in stereo

Input1 “Lvl (Level)”	(1.1–3a)	127
Input1 “Pan”	(1.1–3a)	C064
Input1 “BUS	(1.1–3a)	IFX
(BUS(IFX)Select)”
IFX	select (7.1) 52: Reverb Hall
	and make settings
“Recording Level”	(1.1–2c, 1.1–3e)as appropriate
“Mode (Sample Mode)”	(1.1–2a)	Stereo

Example 3:

A stereo source connected to AUDIO INPUT 1 and 2, and sampling without applying internal effects

Input1 “Lvl (Level)”	(1.1–3a)	127
Input1 “Pan”	(1.1–3a)	L000
Input1 “BUS	(1.1–3a)	L/R
(BUS(IFX)Select)”
Input2 “Lvl (Level)”	(1.1–3a)	127
Input2 “Pan”	(1.1–3a)	R127
Input2 “BUS	(1.1–3a)	L/R
(BUS(IFX)Select)”
“Recording Level”	(1.1–2c, 1.1–3e)as appropriate
“Mode (Sample Mode)”	(1.1–2a)	Stereo

Example 4:

A stereo source connected to AUDIO INPUT 1 and 2, routed through internal insertion effect IFX 08: St.Graphic 7EQ, and sampled in stereo

Input1 “Lvl (Level)”	(1.1–3a)	127
Input1 “Pan”	(1.1–3a)	L000
Input1 “BUS	(1.1–3a)	IFX
(BUS(IFX)Select)”
Input2 “Lvl (Level)”	(1.1–3a)	127
Input2 “Pan”	(1.1–3a)	R127
Input2 “BUS	(1.1–3a)	IFX
(BUS(IFX)Select)”
IFX	select (7.1) 08: St.Graphic
	7EQ and make settings
“Recording Level”	(1.1–2c, 1.1–3e)as appropriate
“Mode (Sample Mode)”	(1.1–2a)	Stereo

When you finish recording a stereo sample, you may hear a slight noise. This does not affect the audio data that has been sampled.

1.1–2b: REC Setup

Mode (REC Mode) [Manual, Auto]

Select s the method by which sampling will be started.

Manual: Sampling will start when you press the [START/ STOP] key from the sampling standby condition.

1Press the [REC/WRITE] key to enter sampling standby mode.

2Use the “Recording Level” (1.1–2c, 1.1–3e) slider to adjust the sampling level.

Be careful of changes in the monitoring volume level (☞ “Recording Level”).

3Sampling will begin when you press the [START/STOP] key. If you use the “Count Down” function, pressing the [START/STOP] key will cause sampling to begin after the metronome sounds a count-down.

4To stop sampling, press the [START/STOP] key once again. Sampling will end automatically if you continue sampling to the end of the “Time (Sample Time)” (1.1– 2a).

Auto: Sampling will begin automatically when the input level exceeds the “Threshold” setting.

1Perform steps 1 and 2 described above.

2Adjust the “Threshold” setting. The black triangles at both sides of the “Recording Level” level bar display will indicate the “Threshold” level. Normally, this should be set as low as possible without allowing noise to trigger sampling.

3Press the [START/STOP] key.

Sampling will automatically begin when the input level exceeds the “Threshold” setting.

4When you are finished sampling, perform step 4 of the Manual procedure.

Threshold [–63dB...0dB]

When performing auto sampling (“Mode (REC Mode)” Auto), this sets the level at which sampling will begin (☞ “Mode (REC Mode)” Auto, step 2).

This will not be displayed if “Mode (REC Mode)” is set to Manual.

7.1 5.2 5.1 4.1 3.1 2.1 1.1 SMPL

91