Korg Electric Keyboard manual 48 St.AutoPanDly, LCR BPM Delay, 191, Stereo Auto Panning Delay

a: Pol, b: Threshold, b: Offset, c: Attack, d: Release

The “Offset” parameter specifies the value for the “Ctrl Target” parameter (that is set to None), expressed as the ratio relative to the parameter value (the “W/D” value with “Ctrl Target”=Out, or the “Feedback” value with “Ctrl Target”=FB).

When “Pol” is positive, the “Ctrl Target” value is obtained by multiplying the parameter value by the “Offset” value (if the input level is below the threshold), or equals the parameter value if the input level exceeds the threshold.

When “Pol” is negative, Ctrl Target value equals the parameter value if the input level is below the threshold, or is obtained by multiplying the parameter value by the “Offset” value if the level exceeds the threshold.

The “Attack” and “Release” parameters specify attack time and release time of delay level control.

Level	Dynamic Delay
Dry	Threshold
Envelope	Release
	Attack
Wet	(Ducking Delay)
Control Target=Out
Polarity= (–)
	Delay Time
Wet
Control Target=Out
Polarity= (+)
	Time

48: St.AutoPanDly

(Stereo Auto Panning Delay)

This stereo delay effect pans the delay sound left and right using the LFO.

Stereo In - Stereo Out

Left

Wet / Dry

High Damp Low Damp

Delay Pan

Feedback Depth

Delay Pan

High Damp Low Damp

Right

	Wet / Dry
	LFO Phase
LFO: Tri / Sin	LFO Shape

a	L Delay (L Delay Time)	0.0...680.0ms
	Sets the delay time for the left channel
b	R Delay (R Delay Time)	0.0...680.0ms
	Sets the delay time for the right channel
c	L Feedback	–100...+100
	Sets the feedback amount for the left channel
d	R Feedback	–100...+100
	Sets the feedback amount for the right channel
	HiDamp (High Damp)		0...100%
e	Sets the damping amount in the high range		☞ Fx:43
	LoDamp (Low Damp)		0...100%
	Sets the damping amount in the low range		☞ Fx:43
	LFO Wave (LFO Waveform)		Tri, Sine
f	Selects LFO Waveform
	Shape (LFO Shape)	–100...+100
	Determines how much the LFO waveform is changed		☞ Fx:20
g	LFO Phase	–180...+180deg
	Sets the LFO phase difference between the left and right		☞ Fx:34
h	Pan Freq (Panning Frequency)	0.02...20.00Hz
	Sets the panning speed

	Pan Dep (Panning Depth)	0...100
	Sets the panning width
i	(Source)	Off...Tempo
	Selects the modulation source for the panning width
	(Amount)	–100...+100
	Set the modulation amount of the panning width
	W/D (Wet/Dly)	Dry, 1:99...99:1, Wet
	Sets the balance between the effect and dry sounds
j	(Source)	Off...Tempo
	Selects the modulation source of the effect balance
	(Amount)	–100...+100
	Sets the modulation amount of the effect balance

49: LCR BPM Delay

(L/C/R BPM Delay)

The L/C/R delay enables you to match the delay time with the song tempo. You can also synchronize the delay time with the arpeggiator or sequencer. If you program the tempo before performance, you can achieve a delay effect that syn- chronizes with the song in real-time. Delay time is set by notes.

Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Left				Wet / Dry
		Input Level D-mod	L Delay	Level
	+	High Damp Low Damp	C Delay	Spread
				Level
			Feedback
		Input Level D-mod	R Delay	Level
Right				Wet / Dry
Tempo
		BPM
BPM		Base Note x Times
		Base Note x Times
		Base Note x Times

a	BPM	MIDI, 40...240
	Selects MIDI Clock and assigns tempo	☞ ,
	L Bs (L Delay Base Note)
	Selects the type of notes to specify the delay time for TapL
		☞ ,
b	Times		1...16
	Sets the number of notes to specify the delay time for TapL			☞
	Level		0...50
	Sets the output level of TapL
	C Bs (C Delay Base Note)
	Selects the type of notes to specify the delay time for TapC
		☞ ,
c	Times		1...16
	Sets the number of notes to specify the delay time for TapC			☞
	Level		0...50
	Sets the output level of TapC
	R Bs (R Delay Base Note)
	Selects the type of notes to specify the delay time for TapR
		☞ ,
d	Times		1...16
	Sets the number of notes to specify the delay time for TapR			☞
	Level		0...50
	Sets the output level of TapR
	C Fb (C Delay Feedback)	–100...+100
	Sets the feedback amount of TapC
e	(Source)	Off...Tempo
	Selects the modulation source for the TapC feedback
	(Amount)	–100...+100
	Sets the modulation amount of the TapC feedback
	Time Over? >	----, OVER!
f	Displays an error message when the delay time exceeds the upper
	limit			☞
	HiDamp (High Damp)		0...100%
g	Sets the damping amount in the high range		☞ Fx:43
	LoDamp (Low Damp)		0...100%
	Sets the damping amount in the low range		☞ Fx:43

Effect

191