Korg Electric Keyboard manual 2b Routing, 2a InsertFX Setup, IFX Insert Effect, 3a Utility

4 If you check “Post IFX Mixer Setting,” the “Pan (CC#8),”	control change CC#91 will control the Send 2 level.
“BUS Select,” “S1 (Send1(MFX1))” and “S2	These messages are received on the global MIDI chan-
(Send2(MFX2))” settings that follow the copy source	nel specified by “MIDI Channel” (GLOBAL 2.1–1a).

insert effect will also be copied. If you do not check this,
only the effect type and its parameters will be copied.
	7.1–2b: Routing
5 To execute the Copy Insert Effect command, press the
[F8] (“OK”) key. To cancel, press the [F7] (“Cancel”) key.	This displays the status of the insert effect.

2.1 1.1 PROG

7.1–2: Setup

Here you can select the type of insert effect, turn it on/off, pan etc.

The direct sound (Dry) of an insert effect is always stereo input and output. The input/output of the effect sound (Wet) will depend on the effect type (☞ p.156).

7.1–2a

7.1–2b

7.1–2c

7.1–2a: InsertFX Setup

IFX On/Off [Off, ON]

Selects the insert effect on/off.

When this is Off, the input will be output without change. (For 00: No Effect, on/off will produce the same result.)

Separately from this setting, you can use control change #92 to turn off insert effect. A value of 0 will be off, and a value of 1–127will be the original setting. This mes- sage is received on the global MIDI channel specified by “MIDI Channel” (GLOBAL 2.1–1a).

Insert Effect [00...89: name]

Indicates the type of insert effect.

For “Insert Effect” you can select from 89 types of effect: 01:

St.Amp Sim – 89: Reverb-Gate.

These effects can also be selected by category in Utility “Select by Category” (7.1–2c).

Pan(CC#8) (Post IFX Pan CC#8) [L000...C064...R127]

Sets the pan after the sound has passed through the insert effect. This setting is valid only when the “BUS Select” from the IFX output is set to L/R (☞ p.158).

CC#8 will control the pan amount.

BUS Select [L/R, 1, 2, 1/2, Off]

Specifies the bus to which the sound will be sent after pass- ing through the insert effect. Normally you will set this to L/ R. If you wish to output to AUDIO OUTPUT (INDIVID- UAL), set this to 1, 2 or 1/2. The Off setting is used when you wish to use “S1 (Send1(MFX1))” and “S2 (Send2(MFX2))” and in addition connect to the master effects in series.

S1 (Send1(MFX1))	[000...	127]
S2 (Send2(MFX2))	[000...	127]

Sets the send levels to the master effects 1 and 2 for the sound that has passed through the insert effect. These set- tings are valid when “BUS Select” (7.1–1a) has been set to L/ R or Off.

Control change CC#93 will control the Send 1 level, and

This displays the routing of the insert effect, the specified effect name, and the on/off status.

You can select (All OSCs) and use the VALUE controller to specify “BUS Select” (☞ 7.1–1a).

■7.1–2c: UTILITY

☞“Write Program” (1.1–1c), “Copy Insert Effect” (7.1–1c)

For details on how to select the desired utility function, refer to “PROG 1.1–1c: UTILITY.”

Select by Category

Selects insert effect by category.

For the procedure, refer to “Select by Category” (☞ p.2).

This command is valid when the 7.1–2a parameters are selected.

7.1–3: IFX (Insert Effect)

Here you can set the effect parameters for the IFX that was selected in the Setup page (☞ p.164–).

7.1–3a

Effect dynamic modulation (Dmod) is controlled on the global MIDI channel “MIDI Channel” (GLOBAL 2.1– 1a). (☞ p.217 “Dynamic Modulation Source (Dmod)” )

■7.1–3a: UTILITY

☞“Write Program” (1.1–1c)

7.2 7.1 6.1 5.3 5.2 5.1 4.2 4.1 3.1 2.2

27