Korg Electric Keyboard manual Global 6.1 Arp.Pattern, 135, 1a Arp, pat Pattern, Tempo

Enable Note Off (Note Off Receive)

On (checked): Note-off messages will be received. Normally you will uncheck this. This parameter is valid when “Hold” (PROG 2.1–1b) is checked (Hold On). In the case of a drum program, you will normally select Hold On. In this case if “Enable Note Off” is checked, note-off messages will be received, and the sound will stop (the release segment of the EG will begin) when the key is released.

Mixer:

Pan [Rndm, L001...C064...R127]

Specifies the panning for each key. With a setting of Rndm (Random), the panning of the drumsample will change ran- domly for each note-on.

BUS (Bus Select) [L/R, IFX, 1, 2, 1/2, Off]

Specifies the bus to which each key will be sent.

For example you can send snare-type sounds to IFX to apply the insert effect, and send the other sounds to L/R without applying the insert effect.

S1 (Send1 (to MFX1))	[000...	127]
S2 (Send2 (to MFX2))	[000...	127]

For each key, specify the send levels to master effects 1 and

2.These settings are valid when “BUS Select” (5.1–3a) is set to L/R or Off.

If “BUS Select” is set to IFX, the send level to master effects 1 and 2 will be determined by the Program, Combination, or Sequencer mode Setup pages (PROG/COMBI 7.1–2, SEQ 7.1–3) S1 (Send1(MFX1),” “S2 (Send2(MFX2)” which are located after the sound passes through IFX.

Drum kits will sound using the settings of the program that is selected in Program mode. These settings are valid only if “Use DKit Setting” (PROG 5.1–1b) and “Use DKit Setting” (PROG 7.1–1a) are checked. Be aware that the results of editing a drum kit will not be reflected unless these settings have been made in the program.

If you moved here from Sequencer mode: Your editing will apply to the arpeggio pattern specified for the selected song. Even if you moved here from settings in which the arpeggia- tor was turned off, you can use the [ARP ON/OFF] key to turn it on. However, it is not possible to turn on an arpeggia- tor for which the “Arpeggiator Run” (SEQ 6.1–1(2)a) param- eter A or B is not checked. Also, the arpeggiator will not operate if it has not been assigned to a track in “Assign” (SEQ 6.1–1(2)b).

In each of the above cases, you can modify the settings of the arpeggio pattern even if the arpeggiator is not turned on. When editing a pattern, it is a good idea to turn on the arpeggiator and make sure that it is the pattern that you wish to edit.

If you want the edited user arpeggio pattern settings to be backed up even when the power is turned off, you must write them into memory. Select the Utility “Write Arpeggio Pattern” to access the Write Arpeggio Pattern dialog box. Alternatively, press the [REC/WRITE] key to access the “Update Arpeggio Patterns” dialog box. Then press the [F8] (“OK”) key to write the edited data.

If you moved here from Sampling mode (if the EXB- SMPL option is installed): The arpeggiator will not turn on, nor will it be possible to edit the arpeggio pattern.

☞For details on creating an arpeggio pattern, refer to BG p.99.

6.1–1: Setup

6.1–1a

6.1–1b

6.1–1c

6.1–1d6.1–1e

2.1 1.1 GLOBAL

■5.1–3b: UTILITY

☞“Write Drum Kits,” “Rename Drum Kit,” “Copy Drum Kit,” “Copy Key Setup” (5.1–1d)

GLOBAL 6.1: Arp.Pattern

Here you can create user arpeggio patterns.

In this page, the TRITON Le will sound as it did in the mode you were in before entering Global mode.

If you moved here from Program mode: Your editing will apply to the arpeggio pattern that is selected by the pro- gram. Even if you moved from a program in which the arpeggiator is turned off, it can be turned on by the [ARP ON/OFF] key.

If you moved here from Combination mode: Your editing will apply to the arpeggio pattern that is selected by the combination. Even if you moved from a combination in which the arpeggiator is turned off, it can be turned on by the [ARP ON/OFF] key.

However, it is not possible to turn on an arpeggiator for which the A or B parameter is unchecked in “Arpeggiator Run” (COMBI 1.1–4(5)a, COMBI 6.1–1a). Also, the arpeggia- tor will not run unless it has been assigned to a timbre in “Assign” (COMBI 6.1–1b).

6.1–1a: Arp, pat (Pattern), (Tempo)

Arp (Arpeggio Select) [A, B]

If you have moved from Combination mode or Sequencer mode and edit an arpeggio pattern, you must select either arpeggiator A or B as the pattern to edit. Your editing will apply only to the selected one.

B will not be displayed if you moved here from Program mode.

Pat (Pattern) [P000...P004, U000(INT)...U215(User)]

Selects the pattern that you wish to edit.

P000 …P004	Preset Arpeggio Patterns
U000(INT)...199(INT)	Preload Arpeggio Patterns
U200(User)...215(User)	for user Arpeggio Patterns
(Tempo)	[040...240, EXT]

Specify the tempo.

This can also be adjusted by the REALTIME CONTROLS C- mode [TEMPO] knobs. If “MIDI Clock” (2.1–1a) is External, the display will indicate EXT and the arpeggiator will syn- chronize to MIDI Clock messages from an external MIDI device.

6.1 5.1 4.1 3.1

135