Latch*

[Off, On]

Specifies whether or not the arpeggio will continue playing after you take your hand off the keyboard.

On (checked): The arpeggio will continue playing after you remove your hand from the keyboard.

Off (unchecked): The arpeggio will stop when you remove your hand from the keyboard.

Key Sync.*

[Off, On]

Specifies whether the arpeggio pattern will begin when you press a key, or whether it will always follow the “ (Tempo)” setting.

On (checked): The arpeggio pattern will start playing from the beginning when a note-on occurs from a condition where no keys are pressed. This setting is suitable when you are playing in realtime and want the arpeggio to play from the beginning of the measure.

Off (unchecked): The arpeggio pattern will always play

according to the “

(Tempo) .”

Keyboard*

[Off, On]

This specifies whether the notes you play on the keyboard will be sounded as usual in addition to being sounded as part of the arpeggio.

On (checked): The notes you play will be sounded on their own, in addition to being sounded as part of the arpeggio. For example if you simultaneously press two or more notes, they will be sounded as usual in addition to being played as arpeggiated notes.

Off (unchecked): Only the arpeggiated notes will be heard.

* These parameters can also be set in “1.1–3: Arp.”

6.1–1b: Arpeggiator Tempo

(Tempo)

[040...240, EXT]

Sets the tempo.

This can also be set by the REALTIME CONTROLS C-mode [TEMPO] knob. When “MIDI Clock” (GLOBAL 2.1–1a) is either External, this will indicate EXT, and the arpeggiator will synchronize to MIDI Clock messages received from an external MIDI device.

6.1–1c: UTILITY

“Write Program” (1.1–1c)

For details on how to select the desired utility function, refer to “PROG 1.1–1c: UTILITY.”

Copy Arpeggiator

This command copies arpeggio settings.

1Select “Copy Arpeggiator” to access the dialog box.

2In “From” specify the copy source arpeggio settings (mode, bank, number).

3If you are copying from Combination or Song, specify whether you wish to copy from A or B.

4To execute the Copy Arpeggio operation, press the [F8] (“OK”) key. To cancel, press the [F7] (“Cancel”) key.

6.1–2: Zone (Scan Zone)

6.1–2a

6.1–2b

6.1–2a: Scan Zone

Zone Map

This shows the “Scan Zone” setting.

Key:

 

 

Btm (Bottom Key)

[C–1...

G9]

Top (Top Key)

[C–1...

G9]

These parameters specify the range of notes (keys) for which the arpeggiator will function. “Top” is the upper limit, and “Btm” is the lower limit.

Vel:

 

 

Btm (Bottom Velocity)

[001...

127]

Top (Top Velocity)

[001...

127]

Specifies the range of velocities for which the arpeggiator will function. “Top” is the upper limit, and “Btm” is the lower limit.

The note number and velocity can also be specified by holding down the [ENTER] key and pressing a note on the keyboard.

6.1–2b: UTILITY

“Write Program” (1.1–1c), “Copy Arpeggiator” (6.1–1c)

7.2 7.1 6.1 5.3 5.2 5.1 4.2 4.1 3.1 2.2 2.1 1.1 PROG

25

Page 32
Image 32
Korg Electric Keyboard manual Zone Scan Zone, 1b Arpeggiator Tempo, 2a Scan Zone