Korg Electric Keyboard manual Insert Effect IFX, In/Out, Routing, 156, Program mode

The following table shows the parameters related to the level settings:

Program mode

Input	OSC1/2 High, Low Level	(PROG 2.1)
	Filter1/2 Trim	(PROG 4.1, 4.2)
	Amp1/2 Level	(PROG 5.1, 5.2)
	OSC1/2 Send1/2	(PROG 7.1)
	Effect Trim parameter *1	(PROG 7.1, 7.2)
Output	Effect W/D parameter	(PROG 7.1, 7.2)
	Rtn1/2 (Return1, 2)	(PROG 7.2)

Combination mode

Input	Volume	(COMBI 1.1, 2.1)
	S1/2 (Send1/2)	(COMBI 7.1)
	Effect Trim parameter *1	(COMBI 7.1, 7.2)
Output	Effect W/D parameter	(COMBI 7.1, 7.2)
	Rtn1/2 (Return1, 2)	(COMBI 7.2)

Sequencer mode

Input	Volume	(SEQ 1.1)
	S1/2 (Send1/2)	(SEQ 7.1)
	Effect Trim parameter *1	(SEQ 7.1, 7.2)
Output	Effect W/D parameter	(SEQ 7.1, 7.2)
	Rtn1/2 (Return1. 2)	(SEQ 7.2)

Sampling mode (if the separately sold EXB-SMPL option is installed)

Input	Rear panel AUDIO INPUT LEVEL
	Input1/2 Lvl (Level)	(SMPL 1.1)
	Effect Trim parameter *1	(SMPL 7.1)
Output	Effect W/D parameter	(SMPL 7.1)

Global mode *2 (if the separately sold EXB-SMPL option is installed)

Input	Rear panel AUDIO INPUT LEVEL
	Input1/2 (Level)	(GLOBAL 1.1)
	Input1/2 Send1/2	(GLOBAL 1.1)

*1:Some effects may not have these parameters.

*2:Use this parameter to set the Audio Input Level in all modes other than Sampling mode.

Insert Effect (IFX)

1. In/Out

Insert Effect (IFX) have a stereo input and a stereo output. If you select Dry (no effect) for the “W/D” parameter, the stereo input signal will be output in stereo without being processed by the effect. If you select Wet (effect applied), the processed signal will be output in one of the following ways:

	Mono In - Mono Out	+	Effect
Wet	Mono In - Stereo Out	+	Effect
	Stereo In - Stereo Out		Effect
			Effect

If you select 00: No Effect, stereo input signals are output in stereo without being processed.

The possible routing of effect inputs and outputs is indi- cated in the upper left corner of the block diagram.

These can be switched on/off by the “On/Off” settings in 7.1: Ed-InsertFX (or Insert FX), Setup pages IFX in each mode. When off, the effect will be bypassed. In the same way as for 00: No Effect, the stereo input sound will be out- put in stereo without modification.

Separately from this “On/Off” setting, MIDI control change CC#92 can be received to turn all IFX effect off. A value of 0 is off, and a value of 1–127 restores the original setting. You can also use “FX SW” (GLOBAL 1.1–1b) to turn off IFX in the same way. This is con- trolled on the global MIDI channel “MIDI Channel” (GLOBAL 2.1–1a).

2. Routing

2–1. Program mode

Use “BUS Select” (PROG 7.1–1a) to set the destination bus of the oscillator output.

L/R: The signal is not sent to the Insert Effects. Instead, it is sent to AUDIO OUTPUT (MAIN) L/MONO and R after the Master EQ.

IFX: The signal is sent to Insert Effect IFX.

1, 2, 1/2: The signal is sent to AUDIO OUTPUT (INDIVID- UAL) 1, 2 (☞ p.162 “Individual Outputs”). The signal is not sent to the Insert Effect, Master Effects, and or Master EQ.

Off: The signal is not sent to AUDIO OUTPUT (MAIN L/ MONO, R, (INDIVIDUAL) 1 or 2. (After the Master Effects, the signal is output to AUDIO OUTPUT (MAIN).) Select this option if you connect the Insert Effect with the Master Effects in series, with the send level specified by “MFX1 Send1”and “MFX2 Send2.”

156