Korg Electric Keyboard manual 104, Rate Convert, Reverse, Link

7If you wish to delete the original sample data and over- write it with the edited sample data, check “Overwrite”. Normally, you will leave “Save to No.” at its default set-

ting, and execute without checking “Overwrite.” (☞ p.99 “*1: About “Overwrite””)

8To execute the Volume Ramp command, press the [F8] (“OK”) key. To cancel, press the [F7] (“Cancel”) key.

Rate Convert

This command lowers the sampling rate (frequency) of the sampled data by 2/3, 1/2, 1/3, 1/4, or 1/6. The sampling frequency of input is fixed at 48 kHz, but you can use this command to create “down-sampling” effects. The sample data is thinned to convert it into sample data of a lower sam- pling frequency.

The “Rate Convert” command is always executed on all waveform data of the selected sample, regardless of the “S (Edit Range Start)” and “E (Edit Range End)” (2.1–2b) set- tings.

1Use “SMPL” (2.1–1a) to select the sample that you wish to edit.

2In the Edit2 page “UTILITY,” choose “Rate Convert” to open the following dialog box.

3The sampling rate of the selected sample is shown at the right of “Rate.” At the right of the “->” you can select the desired amount of the sampling rate conversion: 2/3, 1/2, 1/3, 1/4, 1/6. The sampling rate following conversion will be displayed.

4In “Save to No.,” specify the save destination sample number. By default, an unused sample number will be selected. If you have checked “Overwrite,” this cannot be set.

For a stereo sample, “Save to No.(L)” and “(R)” will be displayed. Specify the save destination sample number for the L channel and R channel respectively.

5If you wish to delete the original sample data and over- write it with the edited sample data, check “Overwrite”. Normally, you will leave “Save to No.” at its default set-

ting, and execute without checking “Overwrite.” (☞ p.99 “*1: About “Overwrite””)

6To execute the Insert Zero command, press the [F8] (“OK”) key. To cancel, press the [F7] (“Cancel”) key.

This command cannot be executed on a sample whose sampling rate is less than 11.025 kHz.

Stereo samples must have the same sampling rate. Although it is possible to select mono multisamples for -L and -R and convert their sampling rate separately, they can no longer be handled as a stereo sample in this case.

Reverse

This command reverses the sample data (i.e., exchanges the beginning and end).

The “Reverse” command is always executed on all wave- form data of the selected sample, regardless of the “S (Edit Range Start)” and “E (Edit Range End)” (2.1–2b) settings.

1Use “SMPL” (2.1–1a) to select the sample that you wish to edit.

2In the Edit2 page “UTILITY,” choose “Reverse” to open the following dialog box.

3In “Save to No.,” specify the save destination sample number. By default, an unused sample number will be selected. If you have checked “Overwrite,” this cannot be set.

For a stereo sample, “Save to No.(L)” and “(R)” will be displayed. Specify the save destination sample number for the L channel and R channel respectively.

4If you wish to delete the original sample data and over- write it with the edited sample data, check “Overwrite”. Normally, you will leave “Save to No.” at its default set-

ting, and execute without checking “Overwrite.” (☞ p.99 “*1: About “Overwrite””)

5To execute the Reverse command, press the [F8] (“OK”) key. To cancel, press the [F7] (“Cancel”) key.

When you execute this command, the entire sample data will be rewritten backward. By using 3.1: Loop Edit “Rev (Reverse)” (3.1–1b), you can reverse the play- back direction without affecting the sample data itself.

Link

This command connects the currently selected sample with another sample.

SOUND A SOUND B

LINK

SOUND A SOUND B

104