PostMIDI: Velocity Curve, After Touch Curve, and Trans- pose will be applied to data before it enters the tone genera- tor.

This means that the Velocity Curve, After Touch Curve, and Transpose settings will affect the data that is sent to the internal tone generator when you play this instrument’s keyboard, when the internal sequencer is played back, or when data is received from MIDI IN.

This setting will not affect the data that is transmitted from MIDI OUT or recorded on the internal sequencer when you play this instrument’s keyboard or playback the sequencer.

 

MIDI IN

Velocity

 

 

 

Curve

 

Record

Play

 

 

 

Sequencer

 

 

 

 

Aftertouch

 

 

 

Curve

 

 

Scale

Transpose

Tone

 

generator

 

 

 

 

 

Pitch change

 

 

MIDI OUT

 

 

Local Control On

[Off, On]

On (checked) Local Control On: The keyboard, joystick, REALTIME CONTROLS knobs [1]–[4], [SW1], and [SW2] keys of this instrument will controls its internal tone genera- tor.

Off (unchecked) Local Control Off: The keyboard, joystick, and REALTIME CONTROLS knobs [1]–[4] etc. of this instru- ment will be disconnected from the internal tone generator. This means that operating this instrument (using the key- board or joystick to perform, or playing the sequencer) will not produce sound.

Uncheck this setting if the echo-back from an external sequencer causes this instrument to sound in duplicate.

Even if this is unchecked, MIDI transmission and recep- tion will occur as usual. Note messages will be trans- mitted when you play the keyboard, and this instrument’s tone generator will sound when note mes- sages are received.

 

 

Sequencer

Arpeggiator

Local

OFF

Record

Trigger

 

control

 

 

Tone

 

ON

 

 

generator

 

 

 

 

 

MIDI IN

 

 

 

 

MIDI OUT

 

 

 

2.1–1b: MIDI Filter

Enable Program Change

[Off, On]

On (checked): Program changes will be transmitted and received.

In Program mode (PROG 1.1: Play), the program will be switched when a program change message is received on the global MIDI channel specified by “MIDI Channel” (2.1– 1a). When you switch programs, a program change message will be transmitted on the global MIDI channel.

In Combination mode (COMBI 1.1: Play), the combination will be switched when a program change message is received on the global MIDI channel. However, it is possible to set the “Combi (Combi Change)” parameter so that the combination is not switched. When a program change is received on the channel specified for each timbre by “MIDI Channel” (COMBI 3.1–1a), the program of that timbre will be switched. However, the program changes for each timbre will be affected by the setting of the “Program Change” parameter (COMBI 4.1–1a).

When you switch combinations, a program change message will be transmitted on the global MIDI channel, and also transmitted simultaneously on the channel of timbres whose “Status” (COMBI 3.1–1a) is set to EXT or EX2.

In Sequencer mode, incoming program change messages on a channel that corresponds to a track whose “Status” (SEQ 3.1–1(2)a) is set to INT or BTH will switch programs on that track. When you select a song or playback song data will be transmitted on the channels of tracks whose “Status” is set to BTH, EXT, or EX2.

Off (unchecked): Program changes will not be transmitted or received.

Bank (Bank Change)

[Off, On]

On (checked): The Bank Select control change message will be transmitted together with program change messages. This is valid when “Enable Program Change” is checked. Off (unchecked): Bank Select messages will not be transmit- ted or received.

When recording on the internal sequencer, bank select messages will be recorded regardless of this setting. However for playback, this setting will apply.

Combi (Combi Change)

[Off, On]

On (checked): When in COMBI 1.1: Play, an incoming pro- gram change message on the global MIDI channel set by “MIDI Channel” (2.1–1a) will switch combinations. This is valid when “Enable Program Change” is checked. An incoming program change on a channel other than the glo- bal MIDI channel will switch the program of any timbre that matches that MIDI channel.

Off (unchecked): An incoming program change message on the global MIDI channel will switch the program of any tim- bre whose “MIDI Channel” (COMBI 3.1–1a) matches the global MIDI channel. The combination will not be switched. The program changes for each timbre will be affected by the setting of the “Program Change” parameter (COMBI 4.1– 1a).

128

Page 135
Image 135
Korg Electric Keyboard manual 128, 1b Midi Filter