Korg Electric Keyboard Attack Time 00…99, Decay Time 00…99, Slope Time 00…99, Release Time 00…99

R (Release Level) [–99…+99]

Specifies the change in cutoff frequency that will occur when the release time has elapsed.

T (Time):

These parameters specify the time over which each change will occur.

A (Attack Time) [00…99]

Specifies the time over which the level will change from note-on until the attack level is reached.

D (Decay Time) [00…99]

Specifies the time over which the level will change from the attack level to the break point level.

S (Slope Time) [00…99]

Specifies the time over which the level will change after the decay time has elapsed until the sustain level is reached.

R (Release Time) [00…99]

Specifies the time over which the level will change after note-on occurs until the release level is reached.

B (AMS SW Break) [–, 0, +]

Specifies the direction in which “AMS (Level Mod. AMS)” will affect “B (Break Point Level).” When “I (AMS Inten- sity)” has a positive (+) value, a setting of + for this parame- ter will allow “AMS” to raise the EG level, and a setting of – will allow “AMS” to lower the EG level. With a setting of 0 there will be no change.

Filter 1 EG changes (level) (AMS = Velocity, Intensity = a positive (+) value)

Note-on	Note-on	Note-on
Note-off	Note-off	Note-off

Softly played note with “S,” Strongly played note with	Strongly played note with
“A,” and “B” set to + (setting“S,” “A,” and “B” set to +	“S,” “A,” and “B” set to –
of 4.1–5a: Filter 1 EG)

4.1–5c: Time Mod. (Time Modulation)

These settings let you use alternate modulation to control the “T (Time)” parameters of the filter 1 EG.

AMS1 (Time Mod. AMS1) [Off, (KT, EXT)]

5.1 4.2 4.1 3.1 2.2 2.1 1.1 PROG

The specified cutoff frequency

					Note-off
	Attack Level		Sustain Level
Note-on						Release
			Break			Level
			Point				Time
			Level
Start
Level	Attack	Decay		Slope		Release
	Time	Time		Time		Time

Indicates the source that will control the “T (Time)” parame- ters of the filter 1 EG (☞ p.212 “AMS List”).

I (AMS1 Intensity) [–99…+99]

Specifies the depth and direction of the effect that “AMS1 (Time Mod. AMS1)” will have.

For example, if “AMS1 (Time Mod. AMS1)” is set to Flt KTr +/+, the EG “T (Time)” parameters will be controlled by the Keyboard Track (4.1–2a) settings. With positive (+) values of this parameter, positive (+) values of “Ramp (Ramp Set-

7.1 6.1 5.3 5.2

4.1–5b: Level Mod. (Level Modulation)

These settings let you use alternate modulation to control the “L (Level)” parameters of the filter 1 EG.

AMS (Level Mod. AMS) [Off, (KT, EXT)]

Indicates the source that will control the “L (Level)” parame- ters of the filter 1 EG (☞ p.212 “AMS List”).

I (AMS Intensity) [–99…+99]

Specifies the depth and direction of the effect that “AMS (Level Mod. AMS)” will have.

For example, if “AMS (Level Mod. AMS)” is Velocity, and you set “S (AMS SW Start),” “A (AMS SW Attack)” and “B (AMS SW Break)” to + and set “I (AMS Intensity)” to a posi- tive (+) value, the EG levels will rise as you play more strongly. If “Intensity” is set to a negative (–) values, the EG levels will fall as you play more strongly.

With a setting of 0, the levels specified by “Filter 1 EG” (4.1– 5a) will be used, no additional effect is produced.

S (AMS SW Start) [–, 0, +]

Specifies the direction in which “AMS (Level Mod. AMS)” will affect “S (Start Level).” When “I (AMS Intensity)” has a positive (+) value, a setting of + for this parameter will allow “AMS” to raise the EG level, and a setting of – will allow “AMS” to lower the EG level. With a setting of 0 there will be no change.

A (AMS SW Attack) [–, 0, +]

Specifies the direction in which “AMS (Level Mod. AMS)” will affect “A(Attack Level).” When “I (AMS Intensity)” has a positive (+) value, a setting of + for this parameter will allow “AMS” to raise the EG level, and a setting of – will allow “AMS” to lower the EG level. With a setting of 0 there will be no change.

ting)” (4.1–2a) will lengthen the EG times, and negative (–) values of “Ramp (Ramp Setting)” will shorten the EG times. The direction of change is specified by “A (AMS1 SW Attack),” “D (AMS1 SW Decay),” “S (AMS1 SW Slope),” and “R (AMS1 SW Release).”

With a setting of 0, the times specified by “Filter1 EG” (4.1– 5a) will be used.

If “AMS1 (Time Mod. AMS1)” is set to Velocity, positive (+) values of this parameter will cause EG times to lengthen as you play more strongly, and negative (–) values will cause EG times to shorten as you play more strongly.

With a setting of 0, the times specified by “Filter1 EG” will be used.

A (AMS1 SW Attack) [–, 0, +]

Specifies the direction in which “AMS1 (Time Mod. AMS1)” will affect the attack time. With positive (+) values of “I (AMS1 Intensity),” setting this parameter to + will allow AMS1 to lengthen the time, and setting this parameter to – will allow AMS1 to shorten the time. With a setting of 0 there will be no change.

D (AMS1 SW Decay) [–, 0, +]

Specifies the direction in which “AMS1 (Time Mod. AMS1)” will affect the decay time. With positive (+) values of “I (AMS1 Intensity),” setting this parameter to + will allow AMS1 to lengthen the time, and setting this parameter to – will allow AMS1 to shorten the time. With a setting of 0 there will be no change.

S (AMS1 SW Slope) [–, 0, +]

Specifies the direction in which “AMS1 (Time Mod. AMS1)” will affect the slope time. With positive (+) values of “I (AMS1 Intensity),” setting this parameter to + will allow AMS1 to lengthen the time, and setting this parameter to – will allow AMS1 to shorten the time. With a setting of 0 there will be no change.

7.2

17