Korg Electric Keyboard manual 256, Installing Dram Simm sample data RAM modules

8Attach the flat cable as shown in the diagram. Plug the cable all the way into the connector.

When connecting the flat cable, be careful not to touch any part other than the connector on the circuit board.

EXB-SMPLScrew

Washer

Chassis to which the board is attached

Connector

Press in all the way

9Reversing the procedure by which you removed cover “A,” re-attach the cover.

3–2. Installing DRAM SIMM (sample data RAM) modules

Install the 16 Mbyte DRAM SIMM (sample data RAM) included with the EXB-SMPL into the slot.

The memory module will work correctly in either slot. For ease of installation, we suggest that you use SIMM slot 2 first.

You must leave the AC/AC power supply disconnected until you finish the entire process of removing the cover, installing the option board or memory, and reat- taching the cover.

1Make sure that cover “B” has been removed. (☞ “1. Prep- arations for installation,” “2–2. Detaching cover “B” for DRAM SIMM”)

2Remove the DRAM SIMM from its packing pouch.

3Verify the location of the slot into which you wish to install the DRAM SIMM.

Looking from the rear of the TRITON Le, the nearer slot is SIMM slot 2.

Locking	Rear side of the DRAM SIMM		Locking
	72PIN	1PIN	hole
hole

Notch

Catches

Rear panel

4The notched side of the DRAM SIMM is PIN 1. Install the DRAM SIMM with its PIN 1 side aligned with the PIN 1

mark ( ) of the slot.

5At a slant, press the DRAM SIMM firmly all the way into the slot, and raise it to the vertical position until the catches of the slot click into the locking holes of the DRAM SIMM. When doing so, pressing the catches of the slot apart to the left and right will help the board go in smoothly.

Rear side of DRAM SIMM

Press in at a slant

Catch Rear side of DRAM SIMM

Catch

Raise to vertical

Rear side of DRAM SIMM

Rear panel

6Reversing the procedure by which you removed cover “B,” re-attach the cover.

7When all steps have been completed, turn on the power and make sure that the DRAM SIMM has been installed correctly. (☞ “4. Checking after installation”)

3–3. Installing additional DRAM SIMM’s

A maximum of two memory modules can be installed. If you want to use two 32 Mbyte DRAM SIMM mod- ules, the 16 Mbyte DRAM SIMM that you installed when installing the EXB-SMPL must be removed as described in step 3 below.

1Make sure that cover “B” has been removed. (☞ “1. Prep- arations for installation,” “2–2. Detaching cover “B” for DRAM SIMM”)

2A 16 Mbyte DRAM SIMM is installed in the nearer slot. If you want to add only one more memory module, install it in the remaining slot. (☞ ”3–2. Installing DRAM SIMM (sample data RAM) modules,” steps 4 and 5.)

3If you will be installing two DRAM SIMM modules, remove the currently-installed memory. Spread the tabs of the DRAM SIMM slot apart to left and right (after releasing the catches), tilt the DRAM SIMM over at an angle, and pull it out.

Rear side of DRAM SIMM

Rear panel

When you spread the catches of the slot apart, the DRAM SIMM may pop out vigorously and fall into an opening (inside the instrument). Please be careful

4Install DRAM SIMM modules in the two slots as described in steps 4 and 5 of “3–2. Installing DRAM SIMM (sample data RAM) modules.”

5Reversing the procedure by which you removed cover “B,” re-attach the cover.

256