Korg Electric Keyboard 2 1LFO2 OSC1 LFO2, 3 2LFO1 OSC2 LFO1, 1b Freq.Mod Frequency Modulation

Key Sync. [Off, On]

On (checked): Key Sync. will be On. The LFO will start each time you play a note, and an independent LFO will operate for each note.

Off (unchecked): Key Sync. will be Off, and the LFO effect that was started by the first-played note will continue to be applied to each newly-played note. (In this case, “Delay” and “Fade” will be applied only to the LFO when it is first started.)

Fade [00…99]

Specifies the time from when the LFO begins to apply until it reaches the maximum amplitude. When “Key Sync.” is Off, the fade will apply only when the LFO is first started.

How “Fade” affects the LFO (when “Key Sync.”Onis )

Note-on	Note-off
“Fade”
“Delay”
Dly (Delay)	[00…99]

Specifies the time from note-on until the LFO effect begins to apply.

When “Key Sync.” is Off, the delay will apply only when the LFO is first started.

5.3–1b: Freq.Mod (Frequency Modulation)

You can use two alternate modulation sources to adjust the speed of the OSC1 LFO1.

AMS1 (Freq. AMS1)

[Off, (PEG, FEG, AEG, LFO2, KT, EXT)]

Indicates the source that will adjust the frequency of the oscillator 1 LFO1 (☞ p.212 “AMS List”). OSC1 LFO1 can be modulated by OSC1 LFO2.

Int (AMS1 Intensity) [–99…+99]

Specifies the depth and direction of the effect that “AMS1 (Freq. AMS1)” will have.

When this parameter is set to a value of 16, 33, 49, 66, 82, or 99, the LFO frequency being can be increased by a maxi- mum of 2, 4, 8, 16, 32, or 64 times respectively (or decreased by 1/2, 1/4, 1/8, 1/16, 1/32, or 1/64 respectively).

For example, if “AMS1 (Freq. AMS1)” is Note No., positive

(+)values of this parameter will cause the oscillator 1 LFO to speed up as you play higher notes. Negative (–) values will cause the oscillator 1 LFO to slow down as you play higher notes. This change will be centered on the C4 note. If “AMS1 (Freq. AMS1)” is set to JS +Y #01, raising the value of this parameter will cause the oscillator 1 LFO1 speed to increase as the joystick is moved away from yourself. With a setting of +99, moving the joystick all the way away from yourself will increase the LFO speed by approximately 64 times.

AMS2 (Freq. AMS2)

[Off, (PEG, FEG, AEG, LFO2, KT, EXT)]

Int (AMS2 Intensity) [–99…+99]

Indicates settings for a second alternate modulation source that will adjust the frequency of the oscillator 1 LFO1.

☞“AMS1 (Freq. AMS1),” “Int. (AMS1 Intensity)”

5.3–1c: MIDI/Tempo Sync.

(Frequency MIDI/Tempo Sync.)

Sync. (MIDI/Tempo Sync.) [Off, On]

On (checked): The LFO frequency will synchronize to the tempo (MIDI Clock). In this case, the values you specified for “Frequency” (5.3–1a) and “Freq.Mod” (5.3–1b) will be ignored.

Base Note (Sync. Base Note)
[ ,	, ,	, ,	, ,	]
Times (Sync. Times)			[01...16]

When “Sync. (MIDI/Tempo Sync.).” is checked, these When “Sync. (MIDI/Tempo Sync.)” is checked, these parameters specify a note length “Base Note (Sync. Base Note)” relative to “ (Tempo)” and the multiple “Times (Sync. Times)” that will be applied to it. These parameters will determine the frequency of the OSC1 LFO1. For example if “Base Note (Sync. Base Note)” is (quarter note) and “Times (Sync. Times)” is 04, the LFO will perform one cycle every four beats.

Even if you change the “ (Tempo)” setting of the arpeggia- tor or sequencer, the LFO will always perform one cycle every four beats.

■5.3–1d: UTILITY

☞“Write Program” (1.1–1c)

For details on how to select the desired utility function, refer to “PROG 1.1–1c: UTILITY.”

Swap LFO 1&2

This exchanges the settings of LFO 1 and 2. If LFO2 is selected in AMS1 (Freq. AMS1) or AMS2 (Freq. AMS2) of LFO1 Freq.Mod (5.3–1b), then these settings will be invalid for LFO2 after LFO1 and 2 have been exchanged. If you select this from the OSC1 LFO1 or OSC1 LFO2 page, LFO1 and LFO2 of OSC1 will be exchanged.

1Select “Swap LFO 1&2” to access the dialog box.

2To execute, press the [F8] (“OK”) key. To cancel without executing, press the [F7] (“Cancel”) key.

5.3–2: 1LFO2 (OSC1 LFO2)

Here you can make settings for the OSC1 LFO2, which is the second LFO that can be applied to oscillator 1. (☞ “5.3–1: OS1LFO1 (OSC1 LFO1)”) However, it is not possible to use the LFO to apply modulation in “AMS1 (Freq. AMS1)” or “AMS2 (Freq. AMS2)” of Freq. Mod.

5.3–3: 2LFO1 (OSC2 LFO1)

This can be used when “Mode (Oscillator Mode)” (2.1–1a) is set to Double. Here you can make settings for the OSC2 LFO1, which is the first LFO that can be applied to oscillator 2 (☞ “5.3–1: OS1LFO1 (OSC1 LFO1)”).

7.2 7.1 6.1 5.3 5.2 5.1 4.2 4.1 3.1 2.2 2.1 1.1 PROG

23