Korg Electric Keyboard manual Mltband Limit, 165, Multiband Limiter

	Envelope (Envelope Select) L/R Mix, L Only, R Only, L/R Individually
a	Selects from linking both channels, controlling only from left channel,
	only from the right channel, or controlling each channel individually
					☞
b	Ratio	1.0:1...50.0:1, Inf:1
	Sets the signal compression ratio				☞
c	Threshold			–40...0dB
	Sets the level above which the compressor is applied				☞
d	Attack			1...100
	Sets the attack time				☞
e	Release			1...100
	Sets the release time				☞
f	Side PEQ Insert			Off, On
	Toggles between on/off of the trigger signal’s EQ				☞
	Trigger Monitor			Off, On
g	Switches between effect output monitor and trigger signal monitor
					☞
	EQ (Side PEQ Cutoff)			20...12.00kHz
	Sets the EQ center frequency for the trigger signal				☞
h	Q			0.5...10.0
	Sets the EQ bandwidth for the trigger signal
	G (Gain)		–18.0...+18.0dB
	Sets the EQ gain for the trigger signal
	G.Adj (Gain Adjust)		–Inf, –38...+24dB
	Sets the output gain			☞ ,
i	(Source)			Off...Tempo
	Selects the modulation source for the output gain
	(Amount)			–63...+63
	Sets the modulation amount of the output gain
	W/D (Wet/Dly)	Dry, 1:99...99:1, Wet
	Sets the balance between the effect and dry sounds
j	(Source)			Off...Tempo
	Selects the modulation source of the effect balance
	(Amount)			–100...+100
	Sets the modulation amount of the effect balance

a: Envelope

When L/R Mix is selected for this parameter, the left and right channels are linked to control the Limiter using the mixed signal. If L Only (or R Only) is selected, the left and right channels are linked, and the Limiter is controlled via only the left (or right) channel.

With L/R individually, the left and right channels control the Lim- iter individually.

b: Ratio, c: Threshold, i: G.Adj

This parameter sets the signal compression “Ratio”. Compression is applied only when the signal level exceeds the “Threshold” value.

Adjust the output level using the “G.Adj” parameter, since com- pression causes the entire level to be reduced.

	Limiter - Threshold / Ratio
	Ratio=1.0 : 1
Output Level
	Ratio=2.0 : 1
Threshold	Ratio=4.0 : 1
	Ration=Inf : 1
Louder
	Louder
	Input Level

Level	Dry	Ratio=1.0 : 1
		Ratio=2.0 : 1
		Ratio=4.0 : 1
		Threshold
		Ratio=Inf : 1
		Time

d: Attack, e: Release

These parameters set the attack time and release time. A higher attack time will cause the compression to be applied more slowly.

Limiter - Attack / Release

Threshold

Dry

Ratio=Inf : 1

WetAttack=1

Release=1

Ratio=Inf : 1

WetAttack=100

Release=100

Release

Attack

f: Side PEQ Insert, h: EQ, h: Q, h: G

These parameters are used to set the EQ applied to the trigger sig- nal.

The Limiter determines whether the compression is applied or not, based on the post-EQ trigger signal. Setting the equalizer allows you to set the Limiter to respond to any frequency band.

g: Trigger Monitor

Setting this parameter On will cause the trigger signal to be out- put, instead of the effect sound. Use this parameter to check the trigger signal with EQ applied.

Usually, set this to Off.

04: Mltband Limit

(Multiband Limiter)

This effect applies the Limiter to the low range, mid range, and high range of the input signal. You can control dynamics for each range to adjust the sound pressure of the low range, mid range, and high range in a different way from the EQ.

Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left				Wet / Dry
	Band-Pass Filters
	Low		Limiter
		Envelope - Control
+	Mid	Low Offset	Limiter
		Envelope - Control		Gain Adjust
	High	Mid Offset	Limiter
		Envelope - Control
Right		High Offset
				Wet / Dry

a	Ratio	1.0:1...50.0:1, Inf:1
	Sets the signal compression ratio		☞ Fx:03
b	Threshold		–40...0dB
	Sets the level above which the compressor is applied		☞ Fx:03
c	Attack		1...100
	Sets the attack time		☞ Fx:03
d	Release		1...100
	Sets the release time		☞ Fx:03
e	Low Offset		–40...0dB
	Gain of the low-range trigger signal			☞
f	Mid Offset		–40...0dB
	Gain of the mid-range trigger signal			☞
g	High Offset		–40...0dB
	Gain of the high-range trigger signal			☞
	G.Adj (Gain Adjust)	–Inf, –38...+24dB
	Sets the output gain	☞ Fx:03,
h	(Source)		Off...Tempo
	Selects the modulation source for the output gain
	(Amount)		–63...+63
	Sets the modulation amount of the output gain

Effect

165