Korg Electric Keyboard manual Smpl 4.1 Multisample, 116, 1a MS, Index, Keyboard & Index

SMPL 4.1: Multisample

Here you can make settings for multisamples. You can create indexes for a multisample, and then assign a sample to each index. (These basic settings can also be performed in 1.1:

Recording page.) In addition, you can delete, copy, or insert an index, and perform detailed editing such as adjusting the level and pitch of the sample for each index.

4.1–1: Edit1

4.1–1a

4.1–1b

4.1–1c4.1–1d

4.1–1a: MS, Index, Keyboard & Index

MS (Multisample Select) [000...999]

Selects the multisample that you wish to edit (☞ 1.1–1a).

Index [xxx (001...128)/yyy (001...128)]

Select s the index that you wish to edit (☞ 1.1–1a).

To select an index, hold down the [ENTER] key and play a note on the keyboard. The index that includes the note you played will be selected. The specified key will be the base key, and will be displayed in gray in “Keyboard & Index.”

Keyboard & Index (☞ 1.1–1a)

4.1–1b: SMPL, Orig.K, TopK

SMPL (Sample Select)

[----: ---No Assign----, 0000...3999]

This shows the number and name of the sample that is assigned to the selected index. You can also select a sample here (☞ 1.1–1b).

Orig.K (Original Key) [C–1...G9]

Specifies the original key of the sample (☞ 1.1–1b).

TopK (Top Key) [C–1...G9]

Specifies the highest key in the zone of the index. The zone is defined by this “Top Key” (☞ 1.1–1b).

■4.1–1c: INSERT, CUT, COPY, CREATE

INSERT

This creates an index. When you press the [F3] (“INSERT” key, a new index will be created according to the “Pstn (Posi- tion)” setting (1.1–3b, 4.1–3a). At this time, the contents of the index that was cut or copied by “CUT” or “COPY” (i.e., the “Zone Range,” “Orig.K Position,” “Level” and “Pitch”) will be assigned at the same time. (The sample will automat- ically be copied or assigned to a different number.)

If it is not possible to create a new index when you exe- cute “CREATE” or “INSERT,” a dialog box will appear. If this occurs, refer to “CREATE” (1.1–1c).

If you have not yet executed “CUT” or “COPY,” such as immediately after power-on, the new index will be cre- ated according to the “Create (Create Zone Preference)” settings (1.1–3b, 4.1–3a) “Position,” “Zone Range,” and “Orig.K Position” as same as “CREATE.”

CUT

When you press the [F4] (“CUT”) key, this deletes the selected index. At the same time, the contents of the deleted index are copied to the “INSERT” buffer.

COPY

When you press the [F5] (“COPY”) key, this copies the con- tent of the selected index to the “INSERT” buffer.

CREATE

This creates an index. When you press the [F6] (“CREATE”) key, a new index will be created according to the settings of “Position,” “Zone Range,” and “Orig.K Position” (1.1–3b, 4.1–3a) (☞ 1.1–1c).

■4.1–1d: UTILITY

☞“Delete SMPL,” “Copy SMPL,” “Move SMPL,” “Rename SMPL,” “SMPL To Stereo,” “Delete MS,” “Copy MS,” “Move MS,” “Rename MS,” “MS To Stereo/MS To Mono,” “Conv. To Prog,” “Keyboard Disp.” (1.1–3f), “Pitch BPM Adj.” (4.1–2b)

4.1–2: Edit2

4.1–2a

4.1–2b

4.1–2a: Level, Pitch, Constant Pitch

Level [–99...+99]

Adjusts the playback level of the sample. Use this when you need to adjust the level balance between samples within a multisample.

0:Unity level

–:The level will be lowered. At a setting of –99there will be no sound.

+: The level will be raised.

Since in Sampling mode the playback unity level will normally be the maximum level, adjustments in the + direction will have no effect. If Volume (CC#07) or Expression (CC#11) has been assigned to as the B-mode function of a REALTIME CONTROLS knob [1]–[4] and these controllers have been operated, or if these MIDI messages have been received to lower the playback unity level, then adjustments in the + direction will be valid (PROG 2.1–2e Sample Parameter: Level).

116