Korg Electric Keyboard manual Auto Reverse, LCR Delay, 188

42: Auto Reverse

This effect records the input signal and automatically plays it in reverse (the effect is similar to a tape reverse sound).

Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left			Wet / Dry
+		Auto Reverse	Direct
			Mix
		Rec/Reverse Play
		Control
Right			Wet / Dry
D-mod	D-mod
		Envelope Control
	Input
	Envelope Select

a	Rec Mode		Single, Multi
	Sets the recording mode				☞
b	Reverse Time		20...1320ms
	Sets the maximum duration of the reverse playback				☞
	Envelope (Envelope Select)		Dmod, Input
	Selects whether the start and end of recording is controlled via the
c	modulation source or the input signal level		☞ ,
	Src (Source)		Off...Tempo
	Selects the modulation source that controls recording when Enve-
	lope is set to Dmod				☞
d	Threshold			0...100
	Sets the recording start level when Envelope is set to Input				☞
e	Response			0...100
	Sets the speed of the response to the end of recording			☞ Fx:31
f	Direct Mix	Always On, Always Off, Cross Fade
	Selects how a dry sound is mixed			☞ Fx:31
	W/D (Wet/Dly)	Dry, 1:99...99:1, Wet
	Sets the balance between the effect and dry sounds
g	(Source)		Off...Tempo
	Selects the modulation source of the effect balance
	(Amount)		–100...+100
	Sets the modulation amount of the effect balance

a: Rec Mode, b: Reverse Time

When ”Rec Mode“ is set to Single, you can set up to 1320msec for “Reverse Time.” If recording starts during the reverse playback, the playback will be interrupted.

When “Rec Mode” is set to Multi, you can make another record- ing during the reverse playback. However, the maximum Reverse Time is limited to 660msec.

If you wish to record a phrase or rhythm pattern, set “Rec Mode” to Single. If you record only one note, set “Rec Mode” to Multi. The “Reverse Time” parameter specifies the maximum duration of the reverse playback. The part in excess of this limit will not be played in reverse. If you wish to add short pieces of the reverse playback of single notes, make the “Reverse Time” shorter.

			Rec Mode/Reverse Time
Rec	Reverse Rec	Reverse	Envelope Select = Input

Input

Time

Rec Mode = Single

Rec Mode = Multi

Reverse Time Reverse Time

c: Envelope, c: Src, d: Threshold

These parameters select the source to control the start and end of recording.

When “Envelope” is set to Dmod, the input signal will be recorded only when the value of the modulation source selected by the Src parameter is 64 or higher.

When “Envelope” is set to Input, the input signal will be recorded

only when its level exceeds the Threshold level.

When recording is completed, reverse playback starts immedi- ately.

43: LCR Delay

(L/C/R Delay)

This multitap delay outputs three Tap signals to the left, right, and center respectively. You can also adjust the left and right spread of the delay sound.

Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Left		Wet / Dry
Input Level D-mod	L Delay
		Level
+	C Delay	Spread
High Damp Low Damp		Level
	Feedback
Input Level D-mod	R Delay	Level
Right		Wet / Dry

	L Delay (L Delay Time)		0...1360ms
a	Sets the delay time of TapL
	Level		0...50
	Sets the output level of TapL
	C Delay (C Delay Time)		0...1360ms
b	Sets the delay time of TapC
	Level		0...50
	Sets the output level of TapC
	R Delay (R Delay Time)		0...1360ms
c	Sets the delay time of TapR
	Level		0...50
	Sets the output level of TapR
	C Fb (C Delay Feedback)		–100...+100
	Sets the feedback amountof TapC
d	(Source)		Off...Tempo
	Selects the modulation source of the TapC feedback amount
	(Amount)		–100...+100
	Sets the modulation amount of the TapC feedback amount
	HiDamp (High Damp)		0...100%
e	Sets the damping amount in the high range			☞
	LoDamp (Low Damp)		0...100%
	Sets the damping amount in the low range			☞
	InLvl Mod (Input Level Dmod [%])		–100...+100
f	Sets the modulation amount of the input level	☞ Fx:37,
	Src (Source)		Off...Tempo
	Selects the modulation source for the input level		☞ Fx:37
g	Spread		0...50
	Sets the width of the stereo image of the effect sound			☞
	W/D (Wet/Dly)	Dry, 1:99...99:1, Wet
	Sets the balance between the effect and dry sounds
h	(Source)		Off...Tempo
	Selects the modulation source of the effect balance
	(Amount)		–100...+100
	Sets the modulation amount of the effect balance

e: HiDamp, e: LoDamp

These parameters set the damping amount of high range and low range. The tone of the delayed sound becomes darker and lighter as it feeds back.

g: Spread

This parameter sets the pan width of the effect sound. The stereo image is widest with a value of 50, and the effect sound of both channels is output from the center with a value of 0.

188