Korg Electric Keyboard manual Phasr-Cho/Fl, Reverb-Gate, 208, Phaser Chorus/Flanger

88: Phasr–Cho/Fl

(Phaser – Chorus/Flanger)

This effect combines a mono-type phaser and a chorus/

flanger.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left					Wet / Dry
	Phaser		Chorus/Flanger
+	Phaser	EQ	Chorus/Flanger		Normal
			LEQ HEQ	+
		Trim			Output Mode
	Resonance	Phaser	Feedback	–	Wet Invert
		Wet / Dry
				Cho/Flng
Right				Wet / Dry
					Wet / Dry
LFO: Tri / Sine			LFO: Tri / Sine

	[PHS] LFO (LFO Waveform)		Tri, Sine
a	Selects the LFO waveform of the phaser
	F (LFO Frequency)		0.02...20.00Hz
	Sets the LFO speed
	Manu (Manual)		0...100
	Sets the frequency to which the effect is applied
b	Dep (Depth)		0...100
	Sets the depth of LFO modulation
	Res (Resonance)		–100...+100
	Sets the resonance amount		☞ Fx:23
c	Phs W/D (Phaser Wet/Dry)	–Wet...–2:98, Dry, 2:98...Wet
	Sets the phaser effect balance		☞ Fx:10, 23
	[CH/FL] LFO (LFO Waveform)		Tri, Sine
d	Selects the LFO waveform of the chorus/flanger
	F (LFO Frequency)		0.02...20.00Hz
	Sets the LFO speed
	Dly (Delay Time)		0.0...50.0ms
	Sets the delay time
e	Dep (Depth)		0...100
	Sets the depth of LFO modulation
	Fb (Feedback)		–100...+100
	Sets the feedback amount		☞ Fx:20
f	Pre EQ Trim		0...100
	Sets the EQ input level
	LoEQ (Pre Low EQ Gain)		–15...+15dB
g	Sets the gain of Low EQ
	HiEQ (Pre High EQ Gain)		–15...+15dB
	Sets the gain of High EQ
	C/F W/D (Cho/Flng Wet/Dry)	–Wet...–2:98, Dry, 2:98...Wet
h	Sets the effect balance of the chorus/flanger		☞ Fx:10, 20
	Out (Output Mode)		Normal, Wet Inv
	Selects the output mode for the chorus/flanger		☞ Fx:60
	W/D (Wet/Dly)		Dry, 1:99...99:1, Wet
	Sets the balance between the effect and dry sounds
i	(Source)		Off...Tempo
	Selects the modulation source of the effect balance
	(Amount)		–100...+100
	Sets the modulation amount of the effect balance

89: Reverb–Gate

This effect combines a mono-type reverb and a gate.

Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out

Left	Reverb	Wet / Dry
	EQ Trim
+ Pre Delay	Reverb	Gate
	LEQ HEQ	Reverb
		Balance
Right		Wet / Dry

Input Reverb Mix

Input

Gate+Dmpr	Envelope - Control
	D-modEnvelope Select	Gate

a	[REV] Reverb Time	0.1...10.0sec
	Sets the reverberation time
	HiDamp (High Damp)	0...100%
b	Sets the damping amount in the high range
	Pre Dly (Pre Delay)	0...200ms
	Sets the delay time of the reverb sound and gate control signal
c	Pre EQ Trim	0...100
	Sets the EQ input level
	LoEQ (Pre Low EQ Gain)	–15...+15dB
d	Sets the gain of Low EQ
	HiEQ (Pre High EQ Gain)	–15...+15dB
	Sets the gain of High EQ
e	Rev Balance (Reverb Balance)	Dry, 1:99...99:1, Wet
	Sets the reverb effect balance
	[GATE] In Rev Mix (Input Reverb Mix)	Dry, 1:99...99:1, Wet
f	Sets the balance between the dry and reverb sounds of the gate con-
	trol signal.		☞
	Envelope (Envelope Select)	Dmod, Input
	Switches between modulation source control and input signal control
g			☞
	Src (Source)	Off...G2+Dmp
	Selects the modulation source that controls the gate when Envelope
	is set to Dmod		☞
	Threshold	0...100
	Sets the gate threshold level		☞
h
	Polarity		+, –
	Switches between non-invert and invert of the gate on/off state
		☞ Fx:05
	Attack	1...100
i	Sets the attack time	☞ Fx:05
	Release	1...100
	Sets the release time	☞ Fx:05
	W/D (Wet/Dly)	Dry, 1:99...99:1, Wet
	Sets the balance between the effect and dry sounds
j	(Source)	Off...Tempo
	Selects the modulation source of the effect balance
	(Amount)	–100...+100
	Sets the modulation amount of the effect balance

g: Envelope, g:Src, f: In Rev Mix, h: Threshold

The “Envelope” parameter enables you to select whether turning the gate on and off is triggered by the input signal level or con- trolled directly by the modulation source. You can select from Off to G2+Dmp for the Source parameter to specify the modulation source.

When “Envelope” is set to Input, the gate is controlled by the level of signals that are the combination of the dry sound and the reverb sound. When the signal level exceeds the threshold, the gate opens and the reverb sound is output.

Normally, set “In Rev Mix” to Dry (the gate is controlled only by the dry sound). If you wish to extend the gate time, set the “In Rev Mix” value higher and adjust the “Threshold” value.

208