Korg Electric Keyboard manual 124, Pref. System Preference, 2a System Preference

If you turn on the power while holding down the [MENU] key and [EXIT] key, the “Load All (Preload PCG and Demo Songs)” operation will be executed automatically (the LCD will display a message of “Now Writing Internal Memory”), and all PCG data and demo song data will be loaded.

Change all bank references

This command changes all program banks specified for tim- bres in combinations or tracks of songs.

1Select “Change all bank references” to access the dialog box.

2To execute this command for combinations, check “Combi.” To execute this command for songs, check “Song.” If you check “Song,” the program banks within the event data of the multis will also be changed.

3Specify the banks to be changed (“Program Bank”).

4To execute the Change All Bank References command, press the [F8] (“OK”) key. To cancel without executing, press [F7] (“Cancel”) key.

If you change two or more different banks to the same bank, it will not be possible to use this function to change them back to different banks. Be careful that the change destination banks do not overlap.

Half Damper Calibration

If a damper pedal that supports half damper (the separately sold DS–1H option) is connected to the rear panel DAMPER jack, here’s how you can adjust the sensitivity if the damper effect is not applied appropriately.

1Connect the half damper pedal to the DAMPER jack.

2Select “Half Damper Calibration” to access the dialog box.

3Press the half damper pedal, and then release the pedal.

4Press the F8 (“Done”) key.

If the adjustment could not be performed correctly, an error message will appear. Please repeat the procedure.

Since the operation of the half damper pedal is delicate, please use the separately sold DS–1H option. If any other pedal is used, the correct effect may not be obtained, or adjustment may not be possible.

After Touch Calibration

If the aftertouch effect depth does not function appropri- ately, you can adjust the sensitivity. Perform the following adjustment if the sensitivity of the aftertouch effect is not correct, such as when aftertouch fails to reach the maximum value.

1Select “After Touch Calibration” to access the dialog box.

2Press down a single key for which the aftertouch effect depth does not correctly, and then release it.

3Press the F8 (“Done”) key. If the adjustment could not be performed correctly, an error message will appear, so please repeat the operation.

The depth of the aftertouch effect may differ slightly from key to key.

1.1–2: Pref. (System Preference)

1.1–2a

1.1–2b 1.1–2c

1.1–2a: System Preference

Bank Map [KORG, GM]

Specifies the mapping of programs and combinations rela- tive to Bank Select control change messages (CC#0 upper byte and CC#32 lower byte).

The bank select messages shown in the following table can be received (R) or transmitted (T), corresponding to Pro- gram banks A...D, banks G, g(d) and Combination banks A...C.

Bank	Bank Map: KORG	Bank Map: GM
Bank A	00. 00 R/T		63. 00 R/T
Bank B	00. 01 R/T		63. 01 R/T
Bank C	00. 02 R/T		63. 02 R/T
Bank D	00. 03 R/T		63. 03 R/T
Bank G	121. 00, 121. 01…09 R/T	121.	00, 121. 01…09 R/T
	56. 00 R		56. 00 R
		00.	00, 00. 01...(XG) R
		00.	00, 01. 00...(GS) R
Bank g (d)	120. 00 R/T		120. 00 R/T
	62. 00 R		62. 00 R
		63. 127 R (→ Korg MUTE)
Value: decimal, R: Receive, T: Transmit
Power On Mode		[Reset, Memorize]

Specifies the condition at power-on.

Reset: This instrument will be in Combination mode

COMBI 1.1: Play, and Combination A000 will be selected.

Memorize: The location (mode and page) where you were when the power was last turned off, and the last-selected program or combination number will be selected.

The contents of any parameters that were being edited are not saved by this function. Before turning the power off, you must Write your edits, or after writing save them in Media mode.

124