Korg Electric Keyboard manual Prog 7.1 Ed-InserFX, 1 BUS, 1a BUS, 1b Use DKit Setting

PROG 7.1: Ed–InserFX

☞For details on insertion effect, refer to p.155 “7. Effect Guide.”

CC#93 will control the Send 1 level for OSC 1 and 2, and control change #91 will control the Send 2 level for OSC 1 and 2. These are controlled on the global MIDI channel “MIDI Channel” (GLOBAL 2.1–1a).

The actual send level is determined by summing these values with the send level setting of each oscillator.

7.1–1: BUS

These settings specify the bus on which the output of the oscillator will be sent, and adjust the send levels to the mas- ter effects.

The following diagram shows the LCD screen when “Mode (Oscillator Mode)” (2.1–1a) is set to Single or Double.

7.1–1a

7.1–1c

7.1–1a: BUS

BUS Select:

BUS Select (All OSCs) [L/R, IFX, 1, 2, 1/2, Off]

Specifies the bus to which oscillators 1 and 2 will be sent.

If this is set to 1/2, the oscillator pan settings (5.1–1b, 5.2–1) will be used to output the sound in stereo from AUDIO OUTPUT (INDIVIDUAL) 1/2. When the oscil- lator pan is controlled by CC#10 (pan) or AMS (Alter- nate Modulation Source), the sound will be output with the pan setting that is in effect at note-on. Unlike the case when this is set to L/R to output the sound from (MAIN) L/MONO and R, the pan of a sounding note will not change in real-time.

If you wish to adjust the pan in real-time while playing a note and output the sound from AUDIO OUTPUT (INDIVIDUAL) 1/2, set “BUS Select” to IFX, set “IFX” to 00: No Effect, and set the “BUS Select” (7.1–2a) after passing through IFX to 1/2.

MFX Send:

OSC1 Send1 [000...127]

Sets the volume (send level) at which the output of OSC1 will be sent to master effect 1. This is valid when “BUS Select” is set to L/R or Off.

If “BUS Select” is set to IFX, the send levels to master effect 1 and 2 are set by “S1 (Send1(MFX1))” and “S2 (Send2(MFX2))” (7.1–2a) after passing through IFX of the Setup page.

OSC1 Send2 [000...127]

Sets the volume (send level) at which the output of OSC1 will be sent to master effect 2 (☞ “OSC1 Send1”).

OSC2 Send1	[000...	127]
OSC2 Send2	[000...	127]

Sets the volume (send level) at which the output of OSC2 will be sent to master effects 1 and 2. These parameters will be valid when “Mode (Oscillator Mode)” (2.1–1a) is set to Double and “BUS Select” is set to L/R or Off (☞ “OSC1 Send1”).

7.1–1b: Use DKit Setting

The LCD screen shown below is for when “Mode (Oscillator Mode)” (2.1–1a) is set to Drums.

7.1–1b

	7.1–1c
Use DKit Setting	[Off, On]

This will be available when “Mode (Oscillator Mode)” is set to Drums.

On (checked): The “BUS (BUS Select)” (GLOBAL 5.1–3a) setting for each key of the selected drum kit will be used. Check this when you want to apply an insert effect to an individual drum instrument, or to output an individual drum instrument to one of the AUDIO OUTPUT (INDIVID- UAL) jacks.

If the “Mode (Oscillator Mode)” is Single or Double, this setting has no effect.

Off (unchecked): The setting of the “BUS Select,” “MFX Send” (7.1–1a) parameter described below will be used. All drum instruments will be sent to the specified bus.

■7.1–1c: UTILITY

☞“Write Program” (1.1–1c)

For details on how to select the desired utility function, refer to “PROG 1.1–1c: UTILITY.”

Copy Insert Effect

This command copies effect settings from Program, Combi- nation, Song, or Sampling mode (if the EXB-SMPL option is installed).

1Select “Copy Insert Effect” to access the dialog box.

2In “From” select the copy source mode, bank, and num- ber.

You can use the Bank [A]–[GM] keys to select the bank.

3Select the effect that you wish to copy. You can also copy from a master effect.

If you are copying from a master effect, the result may not be identical, due to differences in the routing and level settings of a master effect.

26