Korg Electric Keyboard manual Arp Arp. Play, 2c Utility, 3a Arpeggiator, 3b Utility

Decay (Decay Time) [–10…+00…+10]

This adjusts the Decay Time and Slope Time of the filter EG and amp EG.

With an adjustment of +00, the value of the program param- eters will be unchanged.

Positive (+) settings will lengthen the Decay Time and Slope Time beyond the values that were set. With an adjustment of +10, the times will be 99.

Negative (–)settings will shorten the Decay Time and Slope Time. With an adjustment of –10, the times will be 0.

IFX Bal (IFX Balance) [–10…+00…+10]

This adjusts the “W/D(Wet/Dry)” setting of the insertion effect.

With an adjustment of +00, the value of the program param- eters will be unchanged.

Positive (+) settings will raise the Wet level above the pro- gram setting, and lower the Dry level. With an adjustment of +10, the setting will be “Wet” - the effected signal only. Negative (–)settings will lower the Wet level below the pro- gram setting, and raise the Dry level. With an adjustment of –10, the setting will be “Dry” - the signal is unaffected.

MFX Bal (MFX Balance) [–10…+00…+10]

This adjusts the master effect “Rtn1 (Return1)” and “Rtn2 (Return2)” (7.2–1a) settings as a whole.

With an adjustment of +00, the value of the program param- eters will be unchanged.

Positive (+) settings will raise the return levels above the program setting.

With an adjustment of +10, the setting will be 127 (maxi- mum).

Negative (–)settings will lower the return levels below the program setting.

With an adjustment of –10, the setting will be 0.

Octave	Octave of OSC 1 and 2
Stretch	Transpose and Tune of OSC 1 and 2
OSC Bal	High Level and Low Level of OSC1 and 2
Level	Amp1 Level, Amp2 Level
Attack	Amp EG Attack Time, Start Level, Attack Level,
	Level Modulation S, Time Modulation A of Amp 1
	and 2, and Filter EG Attack Time of Filter 1 and 2
Decay	AmpEG Decay Time, Slope Time of Amp 1 and 2,
	Filter EG Decay Time and Slope Time of Filter 1
	and 2
IFX Bal	W/D (Wet/Dry) balance of the IFX effect
MFX Bal	Master Effect RTN1, 2 (Return1, 2)

■1.1–2c: UTILITY

☞“Write Program,” “Select by Category” (1.1–1c)

1.1–3: Arp (Arp. Play)

While arpeggiator parameters are for the most part edited in PROG 6.1: Ed-Arp., Some major parameters can be edited here as well. When you are playing in PROG 1.1: Play, you can edit the arpeggiator in realtime, such as changing the arpeggio pattern etc.

You can also use the REALTIME CONTROLS C-mode [TEMPO], [ARP-GATE], and [ARP-VELOCITY] knobs to edit the arpeggio in realtime (☞ BG p.27).

1.1–3a

				1.1–3b
	1.1–3a: Arpeggiator
Pattern		[P000...P004, U000(INT)...U215(User)]
Reso (Resolution)			[ , ,	, , , ]
Octave				[1, 2, 3, 4]
Sort				[Off, On]
Latch				[Off, On]
Key Sync.				[Off, On]
Keyboard				[Off, On]

Make settings for the program arpeggiator (☞ “PROG: Ed-

Arp.”). These parameters can also be set from 6.1: Ed-Arp. setup page (☞ 6.1–1a).

■1.1–3b: UTILITY

☞“Write Program,” “Select by Category” (1.1–1c)

4