Korg Electric Keyboard manual 23b PLAY/MUTE/REC, Solo On/Off, 45a Pan, Volume, Pan Panpot

The program you select here will be used when the song is played or recorded from the beginning. If the program is changed while recording, the program change will be recorded as musical data, and the program will change dur- ing playback. You can also change the program manually during playback. However if program change command is already recorded, the program will change at that point.

If the “Status” (3.1–1(2)a) is INT or BTH, the program can be specified by receiving a MIDI program change. When you switch songs or return to the beginning of the song, tracks whose “Status” is EXT, EX2, or BTH will transmit the bank and program number via MIDI. Tracks whose “Status” is EX2 will display the Bank as “–,” and will transmit via MIDI the bank number speci- fied by “Bank (EX2) MSB” and “Bank (EX2) LSB” in the Param1 page (3.1–1(2)a).

1.1–2(3)b: PLAY/MUTE/REC, SOLO On/Off

PLAY/MUTE/REC [PLAY, MUTE, REC]

Specifies the mute status of each track, and select the record- ing tracks for multi-track recording. During playback or sin- gle track recording (normal recording), you can select PLAY or MUTE for tracks other than the recording track. During multi-track recording, each track can be set to PLAY, MUTE, or REC. Use the [INC][DEC] keys, or the [VALUE] dial to change the setting.

PLAY: The track will play.

MUTE: The track will be muted (silent).

REC: This will appear in single track recording (normal recording). It cannot be selected.

If you have selected multi-track recording (Preference page “Multi REC” on), select REC for the tracks that you wish to record.

SOLO On/Off [SOLO On, SOLO Off]

Turn the Solo function on/off.

Select the box located at the right of “PLAY/MUTE/REC,” and turn the setting on/off. A track for which this is turned on will show an “S” in the box, and only that track will sound. The other tracks will be muted.

In the case of tracks whose “Status” (3.1–1(2)a) is BTH, EXT, or EX2, a track that has been muted by the Mute or Solo functions will not transmit note on/off data on the MIDI channel specified for that track.

If the utility menu command “Solo Selected Track” (1.1–1d) is on, you cannot turn the solo mode off from here, its solo state will take priority. To turn the solo mode off in this case, you must use the utility menu command (1.1-1d) to deselect it. When you press “SOLO On/Off” or a parameter of another track, only that selected track will be soloed, and will be heard.

■1.1–2(3)c: UTILITY

☞“Memory Status,” “Solo Selected Track,” “Rename Song,” “Delete Song,” “Copy From Song,” “Copy From Combi,” “Load Template Song,” “Save Template Song,” “FF/REW Speed,” “Set Location” (1.1–1d)

For details on how to select the desired utility function, refer to “PROG 1.1–1c: UTILITY.”

Select by Category

Select the program for each track by category.

This will appear and can be selected when “Program Select” is selected. (☞ PROG 1.1–1a)

1.1–4: Mix..8 (Mixer T01...08)

1.1–5: Mix..16 (Mixer T09...16)

Here you can set the pan and volume of each track. The pan and volume that you specify here will be used when you playback or record from the beginning of the song. If you change the settings during recording, the changes will be recorded as sequencer data, and pan and volume will change during playback. You can also change the settings during playback. However when the song reaches a location where pan or volume data was recorded, the settings will change as recorded.

1.1–4a

1.1–1c

1.1–4b

1.1–4(5)a: Pan, Volume

Pan (Panpot) [RND, L001...C064...R127]

Sets the pan of tracks 1–16.

L001...C064...R127: A setting of L001 is far left, and R127 is far right. A setting of C064 will reproduce the pan setting of the oscillator in Program mode.

OSC1		OSC2			OSC1: Amp1 Pan=L032
		OSC1: Amp1 Pan=L001
		OSC2: Amp2 Pan=R127			OSC2: Amp2 Pan=R096
Left	Center	Right	Left	Center	Right
		Pan (CC#10)			Pan (CC#10)
		C064			C064
		L032			L032
		L001			L001
		R096			R096
		R127			R127
Left	Center	Right	Left	Center	Right

OSC1OSC2

OSC1: Amp1 Pan=C064

OSC2: Amp2 Pan=C064

Left Center Right

Pan (CC#10)

C064

L032

L001

R096

R127

Left Center Right

If a mono-type insertion effect is inserted, this setting will be ignored. In this case, the 7.1: Insert FX Setup page “Pan (CC#8)” setting will adjust the pan of the sound following the insertion effect. (☞ p.158 “3. Mixer”)

RND: The sound will be panned randomly at each note-on.

If “Status” (3.1–1(2)a) is INT or BTH, CC#10 Panpot can be received to control the panning. When receiving CC#10, a value of 0 or 1 is far left, 64 is center, and 127 is far right. When you change the song or return to the beginning of the song, tracks whose “Status” is EXT, EX2 or BTH will transmit the pan you specify here as a MIDI message (except for RND).

7.2 7.1 6.1 5.2 5.1 4.4 4.3 4.2 4.1 3.4 3.3 3.2 3.1 2.2 2.1 1.2 1.1 SEQ

55