SEQ 7.1: Insert FX

For details on insert effects, refer to p.155 “7. Effect Guide.”.

7.1–1: BUS..8 (BUS T01...08)

7.1–2: BUS..16 (BUS T09...16)

Specifies the bus to which the program oscillator(s) of each track 1–8, 9–16 will be sent. You can also set the amount of signal that will be sent to the master effects.

7.1–1a

1.1–1c

7.1–1b

7.1–1(2)a: BUS Select, Send1(MFX1), Send2(MFX2)

BUS Select

[DKit, L/R, IFX, 1, 2, 1/2, Off]

Specifies the output bus for the program oscillators of tracks 1–8 and 9–16.

The state of the settings can be viewed in the Setup page. (COMBI 7.1–1a)

S1 (Send1(MFX1))

[000...

127]

S2 (Send2(MFX2))

[000...

127]

Here you can adjust the send levels from tracks 1–8, 9–16 to master effects 1 and 2. This is valid when “BUS Select” is set either to L/R or Off. If IFX is selected, the send level to the master effects 1 and 2 is set by the (“S1 (Send1(MFX1))” and “S2 (Send2(MFX2))” parameters located in the Setup page, after the signal passes through IFX.

These settings have no effect if “BUS Select” is set to 1, 2 or 1/2.

The send 1 and 2 settings you make here will be used when the song is played or recorded from the beginning. If you change the settings while recording, the change will be recorded as part of the musical data, and the send amount will change when the data is played back. You can also change these settings during playback. However if send 1 and 2 data has been recorded, the settings will change accordingly.

If “Status” (3.1–1(2)a) is either INT or BTH, CC#93 and #91 can be received to control send 1 and 2 respectively and change their settings. When you switch songs or return to the beginning of a song, tracks whose “Status” is EXT, EX2 or BTH will transmit these settings via MIDI. This data will be transmitted on the MIDI chan- nel of each track as set by “MIDI Channel” (3.1–1(2)a). The actual send level is determined by summing the value of these parameters with the send level settings of the oscillator(s) of the program used by the track (“S1 (Send1(MFX1))” and “S2 (Send2(MFX2))” PROG 7.1– 2a).

7.1–1(2)b: UTILITY

“Memory Status,” “Solo Selected Track” (1.1–1d), “DKit IFX Patch” (COMBI 7.1–1b), “FF/REW Speed,” “Set Loca- tion” (1.1–1d)

For details on how to select the desired utility function, refer to “PROG 1.1–1c: UTILITY.”

Copy Insert Effect

PROG 7.1–1c

However, the MIDI control channel specified in “Control Channel” of the 7.1: Insert FX, Setup page will not be copied.

7.1–3: Setup

Here you can select the type of the insert effects, turn them on/off etc.

7.1–3b

7.1–3a

7.1–3c

 

 

7.1–3d

 

 

 

7.1–3a: Insert FX Setup

 

IFX On/Off

[Off, ON]

Insert Effect

[00...89: name]

Pan(CC#8)

[L000...C064...R127]

BUS Select

[L/R, 1, 2, 1/2, Off]

S1 (Send1(MFX1))

[000...127]

S2 (Send2(MFX2))

[000...127]

These parameters are the same as in Program mode. (PROG 7.1–2)

However, this differs from Program mode in that insert effect dynamic modulation (Dmod) and the “Pan (CC#8),” “Send1(MFX1),” and “Send2(MFX2)” which follow the insert effect are controlled on the MIDI channel specified by “Control Channel” (7.1–1b). The control changes used are the same as in Program mode.

The pan (CC#8) and Send 1 and 2 that you specify here are used when playing or recording from the beginning of the song. If you change these settings while recording, the set- tings will be recorded as musical data, and during playback, the settings will change accordingly. You can also change these settings during playback. However if Pan (CC#8) and Send 1/2 data has already been recorded, the settings will change according to the recorded data.

If the “Status” (3.1–1(2)a) is INT or BTH, receiving CC#8, #93, or #91 will cause the post- insert effect pan and send 1/2 to be controlled, changing the settings. When you change songs or return to the beginning of the song, tracks whose “Status” is BTH, EXT, or EX2 will transmit these settings on the MIDI channel speci- fied by “Control Channel.”

84

Page 91
Image 91
Korg Electric Keyboard manual SEQ 7.1 Insert FX, 1 BUS..8 BUS T01...08 2 BUS..16 BUS T09...16, 3a Insert FX Setup