Korg Electric Keyboard manual Combi 7.2 Ed-MasterFX, 2c Routing Map, BUS Select, 1a MasterFX Setup

7.1–2c: Routing Map, BUS Select

This displays the bus to which the programs used by tim- bres 1–8 will be sent.

Routing Map

This displays the insert effect settings. The routing, the spec- ified effect name, and the on/off status are shown.

T01...8: BUS Sel [DKit, L/R, IFX, 1, 2, 1/2, Off]

While viewing the map, you can specify the bus where each timbre 1–8 will be sent.

Use the cursor keys to select the timbre, and use the [INC]/ [DEC] keys or the [VALUE] dial to set “BUS Select” (7.1–1a). These settings can also be made in “BUS Select” (7.1–1a).

■7.1–2d: UTILITY

☞“Write Combination,” “Solo Selected Timbre” (1.1–1c),“Copy Insert Effect” (PROG 7.1–1c, 7.1–1b), “Dkit IFX Patch” (7.1–1b), “Select by Category” (PROG 7.1–2c)

7.1–3: IFX (Insert Effect)

Here you can adjust the parameters for the IFX that was selected in the Setup page (☞ p.164–).

7.1–3a

COMBI 7.2: Ed–MasterFX

☞For details on master effects, refer to p.155 “7. Effect Guide.”

7.2–1: Setup

Here you can select the type of each master effect, turn it on/off, and make chain and master EQ settings.

With the exception of “MFX1 Control Ch,” “MFX2 Control Ch,” and “MEQ Control Ch,” this is the same as in Program mode. (☞ PROG 7.2: Ed-MasterFX)

7.2–1a

7.2–1b

7.2–1c

7.2–1d 7.2–1e

7.2–1a: MasterFX Setup

MFX1 On/Off, MFX2 On/Off	[Off, ON]
Master Effect 1, 2	[00...89: name]
Rtn 1, 2 (Return 1, 2)	[000...127]

These are the same as in Program mode. Refer to “PROG 7.2–1: Setup.” However, the master effects will be controlled on the “MFX 1, 2 Control Ch” MIDI channel, unlike in Pro- gram mode.

The control changes used are the same as in Program mode.

MFX 1, 2 Control Ch [Ch01...16, G ch]

Selects the MIDI channel that will control dynamic modulation (Dmod) for the master effects.

G ch: The global MIDI channel “MIDI Channel” (GLOBAL 2.1–1a) will be used for control. Normally you will set this parameter to G ch.

4.4 4.3 4.2 4.1 3.4 3.3 3.2 3.1 2.2 2.1 1.1 COMBI

■7.1–3a: UTILITY

☞“Write Combination” (1.1–1c)

7.2–1b: MasterFX Chain

MFX Chain	[Off, On]
Direction (Chain Direction)
	[MFX1→ MFX2, MFX2→ MFX1]
Signal (Chain Signal)	[LR Mix, L Only, R Only]
Level (Chain Level)	[000...127]

These are the same as in Program mode. (☞ PROG 7.2–1: Setup)

7.2–1c: MEQ Ctrl

MEQ Ctrl (MEQ Control Ch) [Ch01...16, G ch]

Selects the MIDI channel that will control dynamic modulation (Dmod) for the master EQ.

G ch: The global MIDI channel “MIDI Channel” (GLOBAL 2.1–1a) will be used for control. Normally you will set this parameter to G ch.

7.2 7.1 6.1

47