Use DKit Setting

[Off, On]

This is valid when “Mode (Oscillator Mode)” (2.1–1a) is set to Drums.

On (checked): The sound will be output at the “Pan” set- ting that has been made for each key of the drum kit (GLO- BAL 5.1–3a). When “Mode (Oscillator Mode)” is Drums, you will normally use this setting.

Off (unchecked): All notes will be output as specified by the “Pan (Amp1 Pan)” setting.

5.1–1c: AMS, Intensity

AMS (Pan AMS) [Off, (PEG, FEG, AEG, LFO, KT, EXT)]

Indicates the source that will modify pan (p.212 “AMS List”). This change will be relative to the “Pan (Amp1 Pan)” setting.

Intensity

[–99…+99]

Specifies the depth of the effect produced by “AMS (Pan AMS).”

For example, if “Pan (Amp1 Pan)” is set to C064 and “AMS (Pan AMS)” is Note Number, positive (+) values of this parameter will cause the sound to move toward the right as the note numbers increase beyond the C4 note (i.e., as you play higher), and toward the left as the note numbers decrease (i.e., as you play lower). Negative (–) values of this parameter will have the opposite effect.

5.1–1d: UTILITY

“Write Program” (1.1–1c), “Copy Oscillator,” “Swap Oscillator” (2.1–1d)

5.1–2: Mod. (Amp1 Modulation)

These settings allow you to apply modulation to amp 1 (for oscillator 1) to modulate the volume.

5.1–2a

5.1–2b

5.1–2c5.1–2d

5.1–2a: Keyboard Track

These parameters let you use keyboard tracking to adjust the volume of oscillator 1. Use the “Key” and “Ramp” parameters to specify how the volume will be affected by the position on the keyboard of the note that you play.

Key (Keyboard Track Key):

Specifies the note number at which keyboard tracking will begin to apply.

The volume will not change between “Low (KBDTrk Key Low)” and “High (KBDTrk Key High).”

You can also input a value by playing a note on the key- board while you hold down the [ENTER] key.

Low (KBDTrk Key Low)

[C–1…G9]

Keyboard tracking will apply to the range of notes below the note number you specify here.

High (KBDTrk Key High)

[C–1…G9]

Keyboard tracking will apply to the range of notes above the note number you specify here.

Ramp (Ramp Setting):

Specifies the angle of the keyboard tracking.

Low (KBDTrk Ramp Low)

[–99…+99]

With positive (+) values of this parameter, the volume will increase as you play notes below the “Low (KBDTrk Key Low)” note number. With negative (–) values, the volume will decrease.

High (KBDTrk Ramp High)

[–99…+99]

With positive (+) values of this parameter, the volume will increase as you play notes above the “High (KBDTrk Key High)” note number. With negative (–) values, the volume will decrease.

Volume change produced by key position and Ramp settings

Volume

 

 

 

 

 

Ramp Low=+99

 

 

Ramp High=+99

Ramp Low=0

 

 

Ramp High=0

Ramp Low=–99

 

 

Ramp High=–99

 

 

 

Key

 

KBDTrk Low

 

 

KBDTrk High

7.2 7.1 6.1 5.3 5.2 5.1 4.2 4.1 3.1 2.2 2.1 1.1 PROG

19

Page 26
Image 26
Korg Electric Keyboard manual 1c AMS, Intensity, 2 Mod. Amp1 Modulation