Korg Electric Keyboard manual 46 St.Mod. Delay, 47 St.DynamicDly, 190, Stereo Modulation Delay

46: St.Mod. Delay

(Stereo Modulation Delay)

This stereo delay uses an LFO to sweep the delay time. The pitch also varies. You will obtain a delay sound with swell and shimmering. You can also control the delay time using a modulation source.

Stereo In - Stereo Out

Left Wet / Dry

Delay

Feedback

Delay

Right Wet / Dry

D-mod

D-mod Response L/R: +/+ +/–

LFO Sync	LFO: Tri / Sine	LFO Shape
		LFO
		LFO Phase	Modulation Mode

	Mod Mode (Modulation Mode)			LFO, Dmod
	Switches between LFO modulation control and modulation source
a	control
	Src (Source)			Off...Tempo
	Selects the modulation source that controls delay time
	Dmod		L/R:+/+, L/R:+/–
b	Reversed L/R control by modulation source			☞ ,
	Respons (Response)			0...30
	Sets the rate of response to the modulation source
	LFO Wave (LFO Waveform)			Tri, Sine
c	Selects LFO Waveform
	Shape (LFO Shape)			–100...+100
	Determines how much the LFO waveform is changed			☞ Fx:20
d	LFO Freq (LFO Frequency)			0.02...20.00Hz
	Sets the LFO speed
	LFO Sync			Off, On
e	Switches LFO reset off/on			☞ ,
	Src (Source)			Off...Tempo
	Selects the modulation source that resets the LFO
	L Phase (L LFO Phase)			–180...+180
f	Sets the phase obtained when the left LFO is reset				☞
	R Phase (R LFO Phase)			–180...+180
	Sets the phase obtained when the right LFO is reset				☞
	L Depth			0...200
g	Sets the depth of the left LFO modulation
	R Depth			0...200
	Sets the depth of the right LFO modulation
	L Dly (L Delay Time)			0.0...500.0
h	Sets the left delay time
	R Dly (R Delay Time)			0.0...500.0
	Sets the right delay time
	L Fb (L Feedback)			–100...+100
i	Sets the feedback amount of left delay
	R Fb (R Feedback)			–100...+100
	Sets the feedback amount of right delay
	W/D (Wet/Dly)	–Wet...–1:99, Dry, 1:99...Wet
	Sets the balance between the effect and dry sounds
		☞ Fx:10,
j	(Source)			Off...Tempo
	Selects the modulation source of the effect balance
	(Amount)			–100...+100
	Sets the modulation amount of the effect balance

b: Dmod

When the modulation source is used for control, this parameter reverses the left and right modulation direction.

e:LFO Sync, e: Src, f: L Phase, f: R Phase

The LFO can be reset via a modulation source.

The “Src” parameter sets the modulation source that resets the LFO. For example, you can assign Gate as a modulation source so that the sweep always starts from the specified point.

“L Phase” and “R Phase” set the phase obtained when the left and right LFOs are reset. In this way, you can create changes in pitch sweep for the left and right channels individually.

The effect is off when a value of the modulation source spec- ified in the “Src” parameter is 63 or smaller, and the effect is on when the value is 64 or higher. The LFO is triggered and reset to the “L Phase” and “R Phase” settings when the value changes from 63 or smaller to 64 or higher.

47: St.DynamicDly

(Stereo Dynamic Delay)

This stereo delay controls the level of delay according to the input signal level. You can use this as a ducking delay that applies delay to the sound only when you play keys at a high velocity or only when the volume level is low.

Stereo In - Stereo Out
Left				Wet / Dry
		High Damp Low Damp
	Delay
		Feedback	Spread
		High Damp Low Damp
	Delay
Right	FB		Out	Wet / Dry
+	Envelope	Attack, Release	Control Target
	Threshold

	Ctrl Target (Control Target)		None, Out, FB
a	Selects from no control, output, and feedback			☞
	Pol (Polarity)			+, –
	Reverses level control			☞
	Threshold		0...100
b	Sets the level to which the effect is applied			☞
	Offset		0...100
	Sets the offset of level control			☞
	Attack		1...100
c	Sets the attack time of level control			☞
	Release		1...100
	Sets the release time of level control			☞
d	L Delay (L Delay Time)		0.0...680.0ms
	Sets the delay time for the left channel
e	R Delay (R Delay Time)		0.0...680.0ms
	Sets the delay time for the right channel
f	Feedback		–100...+100
	Sets the feedback amount
	HiDamp (High Damp)		0...100%
g	Sets the damping amount in the high range		☞ Fx:43
	LoDamp (Low Damp)		0...100%
	Sets the damping amount in the low range		☞ Fx:43
h	Spread		–100...+100
	Sets the width of the stereo image of the effect sound		☞ Fx:43
	W/D (Wet/Dly)	Dry, 1:99...99:1, Wet
	Sets the balance between the effect and dry sounds
i	(Source)		Off...Tempo
	Selects the modulation source of the effect balance
	(Amount)		–100...+100
	Sets the modulation amount of the effect balance

a: Ctrl Target

This parameter selects no level control, delay output control (effect balance), or feedback amount control.

190