Korg Electric Keyboard manual 50 St.BPM Delay, Sequence Dly, 192, Stereo BPM Delay, Sequence Delay

	InLvl Mod (Input Level Dmod [%])		–100...+100
h	Sets the modulation amount of the input level	☞ Fx:37,
	Src (Source)		Off...Tempo
	Selects the modulation source for the input level		☞ Fx:37
i	Spread		0...50
	Sets the width of the stereo image of the effect sound		☞ Fx:43
	W/D (Wet/Dly)	Dry, 1:99...99:1, Wet
	Sets the balance between the effect and dry sounds
j	(Source)		Off...Tempo
	Selects the modulation source of the effect balance
	(Amount)		–100...+100
	Sets the modulation amount of the effect balance

a:BPM, b: L Bs, b: Times, c: C Bs, c: Times, d: R Bs, d: Times

The delay time is the length of the note obtained by multiplying the “Bs” parameter by the Times value, in relation to the tempo specified by the “BPM” parameter (or the MIDI Clock tempo if “BPM” is set to MIDI).

f: Time Over? >

You can set the delay time up to 1365msec. If the delay time exceeds this limit, the error message “OVER!” appears in the dis- play. Set the delay time parameters so that this message will not appear. “Time Over?>” is only a display parameter.

50: St.BPM Delay

(Stereo BPM Delay)

This stereo delay enables you to set the delay time to match the song tempo.

Stereo In - Stereo Out

Left Wet / Dry

		High Damp Low Damp
	Input Level D-mod	Delay
		Feedback
	Input Level D-mod	High Damp Low Damp
		Delay
Right		Wet / Dry
Tempo
	BPM	Adjust [%]
BPM	Base Note x Times
	Base Note x Times	Adjust [%]

a	BPM	MIDI, 40...240
	Selects MIDI Clock and assigns tempo	☞ Fx:49,
	L Bs (L Delay Base Note)
	Selects the type of notes to specify the left channel delay time
		☞ Fx:49,
b	Times	1...16
	Sets the number of notes to specify the left channel delay time
		☞ Fx:49
	Adj (Adjust)	–2.50...+2.50%
	Fine-adjust the left channel delay time
	R Bs (R Delay Base Note)
	Selects the type of notes to specify the right channel delay time
		☞ Fx:49,
c	Times	1...16
	Sets the number of notes to specify the right channel delay time
		☞ Fx:49
	Adj (Adjust)	–2.50...+2.50%
	Fine-adjust the right channel delay time
	L Fb (L Feedback)	–100...+100
	Sets the feedback amount for the left channel
d	(Source)	Off...Tempo
	Selects the modulation source of feedback amount
	(Amount L)	–100...+100
	Sets the modulation amount of the left channel feedback
	R Fb (R Feedback)	–100...+100
e	Sets the feedback amount for the right channel
	(Amount R)	–100...+100
	Sets the modulation amount of the right channel feedback

	Time Over? L >	----, OVER!
	Display the error message if the left channel delay time exceeds the
f	upper limit		☞
	R >	----, OVER!
	Display the error message if the right channel delay time exceeds the
	upper limit		☞
	HiDamp (High Damp)	0...100%
g	Sets the damping amount in the high range	☞ Fx:43
	LoDamp (Low Damp)	0...100%
	Sets the damping amount in the low range	☞ Fx:43
	InLvl Mod (Input Level Mod [%])	–100...+100
h	Sets the modulation amount of the input level	☞ Fx:37,
	Src (Source)	Off...Tempo
	Selects the modulation source for the input level	☞ Fx:37
	W/D (Wet/Dly)	Dry, 1:99...99:1, Wet
	Sets the balance between the effect and dry sounds
i	(Source)	Off...Tempo
	Selects the modulation source of the effect balance
	(Amount)	–100...+100
	Sets the modulation amount of the effect balance

f: Time Over? L >, f: R >

You can set the delay time up to 682msec. If the delay time exceeds this limit, the error message “OVER!” appears in the dis- play. Set the delay time parameters so that this message will not appear. "Time Over?>" is only a display parameter.

51: Sequence Dly

(Sequence Delay)

This four-tap delay enables you to select a tempo and rhythm pattern to set up each tap.

Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Left	Wet / Dry
	Pan
	Input Level D-mod
+	Delay
	High Damp Low Damp
	Feedback
	Input Level D-mod
Right	Wet / Dry
	Tempo
	BPM
	BPM
	Rythm Pattern

	BPM	MIDI, 44...240
a	Selects MIDI Clock and assigns tempo	☞ ,
	Rhythm (Rhythm Pattern)	– – – ...	3
	Selects a rhythm pattern	☞ ,
b	Tap1 Pan	L, 1...99, R
	Sets the panning of Tap1
c	Tap2 Pan	L, 1...99, R
	Sets the panning of Tap2
d	Tap3 Pan	L, 1...99, R
	Sets the panning of Tap3
e	Tap4 Pan	L, 1...99, R
	Sets the panning of Tap4
	Fb (Feedback)	–100...+100
	Sets the feedback amount
f	(Source)	Off...Tempo
	Selects the modulation source of feedback amount
	(Amount)	–100...+100
	Sets the modulation amount of the feedback
	HiDamp (High Damp)	0...100%
g	Sets the damping amount in the high range	☞ Fx:43
	LoDamp (Low Damp)	0...100%
	Sets the damping amount in the low range	☞ Fx:43

192