Korg Electric Keyboard manual Comp-Cho/Fl, Comp-Phaser, 199, Compressor Chorus/Flanger

	C/F W/D (Cho/Flng Wet/Dry)	300...10.00kHz
	Sets the center frequency for Band 3
g	Q	0.5...10.0
	Sets the bandwidth of Band 3	☞ Fx:06
	G (Gain)	–18...+18dB
	Sets the gain of Band 3
	B4 (Band4 Cutoff)	500...20.00kHz
	Sets the center frequency for Band 4
h	Q	0.5...10.0
	Sets the bandwidth of Band 4	☞ Fx:06
	G (Gain)	–18...+18dB
	Sets the gain of Band 4
	W/D (Wet/Dly)	Dry, 1:99...99:1, Wet
	Sets the balance between the effect and dry sounds
i	(Source)	Off...Tempo
	Selects the modulation source of the effect balance
	(Amount)	–100...+100
	Sets the modulation amount of the effect balance

67: Comp–Cho/Fl

(Compressor – Chorus/Flanger)

This effect combines a mono-type compressor and a chorus/ flanger. You can change the order of the effect connection.

Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left				Wet / Dry
		Routing
Compressor
		Chorus/Flanger
EQ Trim LEQ	HEQ
+	Comp	Chorus/Flanger		Normal
	Output Level		+	Output Mode
		Feedback	– Wet Invert
		Cho/Flng Wet / Dry
Right				Wet / Dry
Envelope - Control		LFO: Tri / Sine

a	[CMP] Sensitivity		1...100
	Sets the sensitivity		☞ Fx:02
	Attack		1...100
b	Sets the attack level		☞ Fx:02
	Level (Output Level)		0...100
	Sets the compressor output level		☞ Fx:02
c	Pre EQ Trim		0...100
	Sets the EQ input level
	LoEQ (Pre Low EQ Gain)		–15...+15dB
d	Sets the gain of Low EQ
	HiEQ (Pre High EQ Gain)		–15...+15dB
	Sets the gain of High EQ
	[CH/FL] LFO (LFO Waveform)		Tri, Sine
e	Selects the LFO waveform of the chorus/flanger
	F (LFO Frequency)		0.02...20.00Hz
	Sets the LFO speed
	Dly (Delay Time)		0.0...50.0ms
	Sets the delay time
f	Dep (Depth)		0...100
	Sets the depth of LFO modulation
	Fb (Feedback)		–100...+100
	Sets the feedback amount		☞ Fx:20
	[F] Cho/Flng W/D	–Wet...–2:98, Dry, 2:98...Wet
g	Sets the effect balance of the chorus/flanger		☞ Fx:10, 20
	Out (Output Mode)		Normal, Wet Inv
	Selects the output mode for the chorus/flanger			☞
	[Routing]	CMP → CF/FL, CH/FL → CMP
h	Switches the order of the compressor and chorus/flanger connection
				☞
	W/D (Wet/Dly)	Dry, 1:99...99:1, Wet
	Sets the balance between the effect and dry sounds
i	(Source)		Off...Tempo
	Selects the modulation source of the effect balance
	(Amount)		–100...+100
	Sets the modulation amount of the effect balance

g: Out, h: [Routing]

When Wet Inv is selected, the right channel phase of the chorus/ flanger effect sound is inverted. This creates pseudo-stereo effects and adds spread.

However, if a mono-input type effect is connected after this effect, the left and right sounds may cancel each other, eliminating the chorus/flanger effects.

When “[Routing]” is set to CH/FL→ CMP, “Out” will be set to Normal.

68: Comp–Phaser

(Compressor – Phaser)

This effect combines a mono-type compressor and a phaser. You can change the order of the effect connection.

Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left				Wet / Dry
		Routing
Compressor
		Phaser
EQ Trim LEQ	HEQ
+	Comp	Phaser		Normal
	Output Level		+
				Output Mode
		Resonance	–	Wet Invert
			Phaser Wet / Dry
Right				Wet / Dry
Envelope - Control		LFO: Tri / Sine

a	[CMP] Sensitivity	1...100
	Sets the sensitivity	☞ Fx:02
	Attack	1...100
b	Sets the attack level	☞ Fx:02
	Level (Output Level)	0...100
	Sets the compressor output level	☞ Fx:02
c	Pre EQ Trim	0...100
	Sets the EQ input level
	LoEQ (Pre Low EQ Gain)	–15...+15dB
d	Sets the gain of Low EQ
	HiEQ (Pre High EQ Gain)	–15...+15dB
	Sets the gain of High EQ
	[PHS] LFO (LFO Waveform)	Tri, Sine
e	Selects the LFO waveform of the phaser
	F (LFO Frequency)	0.02...20.00Hz
	Sets the LFO speed
	Manu (Manual)	0...100
	Sets the frequency to which the effect is applied
f	Dep (Depth)	0...100
	Sets the depth of LFO modulation
	Res (Resonance)	–100...+100
	Sets the resonance amount	☞ Fx:23
	Phs W/D (Phaser Wet/Dry)	–Wet...–2:98, Dry, 2:98...Wet
g	Sets the phaser effect balance	☞ Fx:10, 23
	Out (Output Mode)	Normal, Wet Inv
	Selects the phaser output mode	☞ Fx:67
	[Routing]	CMP→ PHS, PHS→ CMP

hSwitches the order of the compressor and phaser connection

☞Fx:67

	W/D (Wet/Dly)	Dry, 1:99...99:1, Wet
	Sets the balance between the effect and dry sounds
i	(Source)	Off...Tempo
	Selects the modulation source of the effect balance
	(Amount)	–100...+100
	Sets the modulation amount of the effect balance

Effect

199