Korg Electric Keyboard manual SW1/2 Assign, SW1, SW2 Assign List, 220

SW1/2 Assign

The following functions can be assigned to the [SW1] or [SW2] keys.

•For a program, combination, or song make the settings in 2.2: Ed-Ctrl/Controller page “SW1/2 Assign” (2.2– 1b).

•In Sampling mode (when the EXB-SMPL option is installed), assign the functions in the 5.2: Controller/ Controls page setting “SW1/2 Assign” (5.2–1b).

This can be set for each program in Program mode, each combination in Combination mode, and each song in Sequencer mode. For Sampling mode, the settings apply to the entire mode.

SW1, SW2 Assign List

Off	no function
SW1 Mod.(CC#80) (SW1 Modulation:CC#80)	Select this when using the switch as an Alternate Modulation or Effect Dynamic Modulation
SW2 Mod.(CC#81) (SW2 Modulation:CC#81)	source. In this case, you must first specify the control destination. Each time the switch is turned
	On/Off, a CC#80 (or CC#81) message will be transmitted (Off: 0, On: 127).	(☞ p.220)
Porta.SW(CC#65) (Portamento Switch:CC#65)	When you press SW1 (or SW2) to turn it on (LED lit), portamento will be applied. Each time this is
	turned On/Off, CC#65 will be transmitted (Off: 0, On: 127).	(☞ p.220)
Octave Down	Each time you press SW1 (or SW2), the pitch will alternate between 1 octave lower
	and the original octave setting (1 octave down when the LED is lit).
Octave Up	Each time you press SW1 (or SW2), the pitch will alternate between 1 octave higher
	and the original octave setting (1 octave up when the LED is lit).
JS X Lock	Lock the effect of the joystick X direction.	(☞ p.220)
JS+Y Lock	Lock the effect of the joystick +Y direction.	(☞ p.220)
JS-Y Lock	Lock the effect of the joystick -Y direction.	(☞ p.220)
Ribbon Lock :N/A	—	(☞ p.220)
JS X&Rbn Lock :N/A	—	(☞ p.220)
JS+Y&Rbn Lock :N/A	—	(☞ p.220)
JS-Y&Rbn Lock :N/A	—	(☞ p.220)
AfterT Lock	Lock the effect of after touch.	(☞ p.220)

SW1 Mod.(CC#80) (SW1 Modulation:CC#80)

SW2 Mod.(CC#81) (SW2 Modulation:CC#81)

This effect differs between SW1 and SW2. SW1 is handled as CC#80, and SW2 is handled as CC#81.

Porta.SW(CC#65) (Portamento Switch:CC#65)

When “Mode (Oscillator Mode)” (PROG 2.1–1a) is Single, turning the switch on (LED lit) will apply portamento regardless of the “Enable (Porta. Enable)” (PROG 3.1–1c) setting, and turning the switch off (LED off) will not apply portamento.

If “Mode (Oscillator Mode)” is Double, and if the “Enable (Porta. Enable)” setting is the same for OSC1 and 2 (i.e., Enable or Disable for both OSC1 and 2), then portamento will be applied to OSC1 and 2 when the switch is turned on (LED lit), and portamento will not be applied to OSC1 and 2 when the switch is turned off (LED off).

If the “Enable (Porta. Enable)” setting is different for OSC1 and 2 (i.e., OSC1 is Enable and OSC2 is Disable, or OSC1 is Disable and OSC2 is Enable), then portamento will be applied to the OSC whose setting is Enable when the switch is turned on (LED lit), and portamento will be applied to neither OSC when the switch is turned off (LED off).

JS X Lock, JS+Y Lock, JS-Y Lock, AfterT Lock

The state of the selected controller (joystick, after touch) will alternate between Lock and Unlock (Lock when the LED is lit).

While the joystick or after touch is being operated, turning Lock on will lock (fix) the effect at the current position of that controller.

For example if you select JS+Y Lock, move the joystick away from yourself, and then turn Lock on, the operation produced by the joystick (+Y) will be locked (held) at that position. Even if you return the joystick to its original posi- tion, the modulation will continue to apply. At this time you can even move the joystick in the –Y direction to apply both types of modulation (joystick +Y and –Y) simultaneously.

When you Lock the joystick or after touch, MIDI trans- mission of the corresponding controller will be halted, but reception will still occur.

Ribbon Lock: N/A, JS X&Rbn Lock : N/A,

JS+Y&Rbn Lock: N/A, JS-Y&Rbn Lock: N/A

These values can be specified, but will have no actual effect. N/A indicates Not Available (i.e., invalid).

Data compatibility is maintained between this instrument and the TRITON/TRITONpro/TRITONproX (TRITON key- board models). Programs created on this instrument can be used on TRITON keyboard models, and the opposite is also true.

In order to maintain compatibility, it is necessary to specify these “invalid” parameters on this instrument.

220