Korg Electric Keyboard 3b Level Mod. Level Modulation, 3c Time Mod. Time Modulation, Off, EXT, KT

R (Release Time) [00…99]

Specifies the time over which the volume will change after note-off until it reaches 0.

Amplifier EG

Attack Level	Note-off
Note-on	Break Point
Volume
	Sustain
Start	Level
	Time
Level

Attack	Decay	Slope	Release Time
Time	Time	Time

5.1–3b: Level Mod. (Level Modulation)

These parameters let you use AMS to modulate the amp 1 EG levels that were specified in “Amp 1 EG” (5.1–3a).

AMS (Level Mod. AMS) [Off, (KT, EXT)]

Selects the source that will control the “Level” parameters of the amp 1 EG (☞ p.212 “AMS List”).

I (AMS Intensity) [–99…+99]

Specifies the depth and direction of the effect that “AMS (Level Mod. AMS)” will have.

For example, if “AMS (Level Mod. AMS)” is Velocity, setting “S (AMS SW Start),” “A (AMS SW Attack),” and “B (AMS SW Break)” to + and setting “Intensity” to a positive (+) value will cause the amp 1 EG volume levels to increase as you play more strongly. Setting “Intensity” to a negative (–) values will cause the amp 1 EG volume levels to decrease as you play more strongly. With a setting of 0, the levels will be as specified in “Amp 1 EG” (5.1–3a).

S (AMS SW Start) [–, 0, +]

Specifies the direction in which “AMS (Level Mod. AMS)” will change “S (Start Level).” If “I (AMS Intensity)” is set to a positive (+) value, setting this parameter to + will allow AMS to increase the EG level, and setting this parameter to – will allow AMS to decrease the EG level. With a setting of 0, no change will occur.

A (AMS SW Attack) [–, 0, +]

Specifies the direction in which “AMS (Level Mod. AMS)” will change “A (Attack Level).” If “I (AMS Intensity)” is set to a positive (+) value, setting this parameter to + will allow AMS to increase the EG level, and setting this parameter to – will allow AMS to decrease the EG level. With a setting of 0, no change will occur.

B (AMS SW Break) [–, 0, +]

Specifies the direction in which “AMS (Level Mod. AMS)” will change “B (Break Point Level).” If “I (AMS Intensity)” is set to a positive (+) value, setting this parameter to + will allow AMS to increase the EG level, and setting this parame- ter to – will allow AMS to decrease the EG level. With a set- ting of 0, no change will occur.

Amp 1 EG changes (Level) (AMS=Velocity, Intensity = a positive (+) value)

	Note-on		Note-on		Note-on
	Note-off		Note-off		Note-off
Softly played note when “S”=0		Strongly played note		Strongly played note
and “A” and “B” are set to +		when “S”=0 and “A” and		when “S”=0 and “A” and
(settings of 5.1–3a: Amp 1 EG)		“B” are set to +		“B” are set to –

5.1–3c: Time Mod. (Time Modulation)

You can use two AMS sources to control the Amp 1 EG times that were specified in “Amp 1 EG” (5.1–3a).

AMS1 (Time Mod. AMS1) [Off, (EXT, KT)]

Selects the source that will control the “Time” parameters of Amp 1 EG. (☞ p.212 “AMS List”)

I (AMS1 Intensity) [–99…+99]

Specifies the depth and direction of the effect that “AMS1 (Time Mod. AMS1)” will have.

For example, if “AMS1 (Time Mod. AMS1)” is Amp KT +/+, the (Amp) “Keyboard Track” settings (5.1–2a) will control the EG “Time” parameters. With positive (+) values of this parameter, positive (+) values of “Ramp (Ramp Setting)” will cause EG times to be lengthened, and negative (–) val- ues of “Ramp (Ramp Setting)” will cause EG times to be shortened. The direction of the change is specified by “A (AMS1 SW Attack),” “D (AMS1 SW Decay),” “S (AMS1 SW Slope),” and “R (AMS1 SW Release).”

When “AMS1 (Time Mod. AMS1)” is Velocity, positive (+) values will cause EG times to lengthen as you play more strongly, and negative (–) values will cause EG times to shorten as you play more strongly. With a setting of 0, the EG times will be as specified in “Amp1 EG” (5.1–3a).

A (AMS1 SW Attack) [–, 0, +]

Specifies the direction of the effect that “AMS1 (Time Mod. AMS1)” will have on “A (Attack Time).” With positive (+) values of “I (AMS1 Intensity),” setting this parameter to + will allow AMS1 to lengthen the time, and setting it to – will allow AMS1 to shorten the time. With a setting of 0 there will be no effect.

D (AMS1 SW Decay) [–, 0, +]

Specifies the direction of the effect that “AMS1 (Time Mod. AMS1)” will have on “D (Decay Time).” With positive (+) values of “I (AMS1 Intensity),” setting this parameter to + will allow AMS1 to lengthen the time, and setting it to – will allow AMS1 to shorten the time. With a setting of 0 there will be no effect.

S (AMS1 SW Slope) [–, 0, +]

Specifies the direction of the effect that “AMS1 (Time Mod. AMS1)” will have on “S (Slope Time).” With positive (+) values of “I (AMS1 Intensity),” setting this parameter to + will allow AMS1 to lengthen the time, and setting it to – will allow AMS1 to shorten the time. With a setting of 0 there will be no effect.

R (AMS1 SW Release) [–, 0, +]

Specifies the direction of the effect that “AMS1 (Time Mod. AMS1)” will have on “R (Release Time).” With positive (+) values of “I (AMS1 Intensity),” setting this parameter to + will allow AMS1 to lengthen the time, and setting it to – will allow AMS1 to shorten the time. With a setting of 0 there will be no effect.

7.2 7.1 6.1 5.3 5.2 5.1 4.2 4.1 3.1 2.2 2.1 1.1 PROG

21