Korg Electric Keyboard manual 07 St.Para.4EQ, 167, Stereo Parametric 4-Band EQ

Level (Output Level)	0...50
Sets the output level	☞ ,
(Source)	Off...Tempo

eSelects the modulation source for the output level

	(Amount)	–50...+50
	Sets the modulation amount of the output level
	Lo (Low Cutoff )	20...1.0kHz
f	Sets the center frequency for Low EQ (shelving type)
	G (Gain)	–18...+18dB
	Sets the gain of Low EQ
	M1 (Mid1 Cutoff)	300...10.00kHz
	Sets the center frequency for Mid/High EQ 1 (peaking type)
g	Q	0.5...10.0
	Sets the band width of Mid/High EQ 1		☞
	G (Gain)	–18...+18dB
	Sets the gain of Mid/High EQ 1
	M2 (Mid2 Cutoff)	500...20.00kHz
	Sets the center frequency for Mid/High EQ 2 (peaking type)
h	Q	0.5...10.0
	Sets the band width of Mid/High EQ 2		☞
	G (Gain)	–18...+18dB
	Sets the gain of Mid/High EQ 2
	Direct Mix	0...50
i	Sets the amount of the dry sound mixed to the distortion
	SpSim (Speaker Simulation)	Off, On
	Switches the speaker simulation on/off
	W/D (Wet/Dly)	Dry, 1:99...99:1, Wet
	Sets the balance between the effect and dry sounds
j	(Source)	Off...Tempo
	Selects the modulation source of the effect balance
	(Amount)	–100...+100
	Sets the modulation amount of the effect balance

a: Wah

The Wah parameter switches the wah effect on/off.

a: (Sw)

This parameter sets how the wah effect is switched on and off via the modulation source.

When “Sw” = Mmnt (Moment), the wah effect is usually turned off. It is turned on only when you press the pedal or operate the joystick.

When a value for the modulation source is less than 64, “off” speed is selected, and when the value is 64 or higher, “on” is selected.

When “(Sw)” = Tggl (Toggle), the wah effect is switched between on and off each time you press the pedal or operate the joystick.

The switch will be turned on/off each time the value of the modulation source exceeds 64.

b: SweepRng, b: Src

This parameter sets the sweep range of the wah center frequency. A negative value will reverse the direction of sweep. The wah cen- ter frequency can be controlled by the modulation source speci- fied in the “Src” parameter.

d: Drive, e: Level

The degree of distortion is determined by the level of input signal and the setting of “Drive”. Raising the “Drive” setting will cause the entire volume level to increase. Use the “Level” parameter to adjust the volume level. The “Level” parameter uses the signal level input to the 3-Band EQ. If clipping occurs at the 3-Band EQ, adjust the “Level” parameter.

d: Pre Low-cut

Cutting the signal in the low range before it is input to the Distor- tion will create a sharp distortion.

g: Q, h: Q

These parameters set the bandwidth of each equalizer. The higher the value, the narrower the band becomes.

07: St.Para.4EQ

(Stereo Parametric 4-Band EQ)

This is a stereo 4-band parametric equalizer. You can select peaking type or shelving type for Band 1 and 4. The gain of Band 2 can be controlled by dynamic modulation.

Stereo In - Stereo Out
Left		Band3 Band4		Wet / Dry
Band1 Band2
PEQ	PEQ	PEQ	PEQ
Trim			HEQ
LEQ
LEQ			HEQ
Trim
PEQ	PEQ	PEQ	PEQ
Right				Wet / Dry
D-mod

a	Trim		0...100
	Sets the input level
b	B1 Type (Band1 Type)	Peaking, Shelving-Low
	Selects the type of Band 1			☞
c	B4 Type (Band4 Type)	Peaking, Shelving-High
	Selects the type of Band 4			☞
	B2 Dyn.G Src (Band2 Dynamic Gain Source)		Off...Tempo
d	Selects the modulation source of the Band 2 gain			☞
	(Amount)		–18...+18dB
	Sets the modulation amount of Band 2 gain			☞
	B1 (Band1 Cutoff)		20...1.00kHz
	Sets the center frequency of Band 1
e	Q		0.5...10.0
	Sets the bandwidth of Band 1		☞ Fx:06
	G (Gain)		–18.0...+18.0dB
	Sets the gain of Band 1
	B2 (Band2 Cutoff)		50...10.00kHz
	Sets the center frequency of Band 2
f	Q		0.5...10.0
	Sets the bandwidth of Band 2		☞ Fx:06
	G (Gain)		–18.0...+18.0dB
	Sets the gain of Band 2		☞ ,
	B3 (Band3 Cutoff)		300...10.00kHz
	Sets the center frequency of Band 3
g	Q		0.5...10.0
	Sets the bandwidth of Band 3		☞ Fx:06
	G (Gain)		–18.0...+18.0dB
	Sets the gain of Band 3
	B4 (Band4 Cutoff)		500...20.00kHz
	Sets the center frequency of Band 4
h	Q		0.5...10.0
	Sets the bandwidth of Band 4		☞ Fx:06
	G (Gain)		–18.0...+18.0dB
	Sets the gain of Band 4
	W/D (Wet/Dly)	Dry, 1:99...99:1, Wet
	Sets the balance between the effect and dry sounds
i	(Source)		Off...Tempo
	Selects the modulation source of the effect balance
	(Amount)		–100...+100
	Sets the modulation amount of the effect balance

b: B1 Type, c: B4 Type

Selects a filter type for Band 1 and 4.

	Parametric 4EQ - Band1, Band4 Type
+Gain	3dB
	Band4 Type=Shelving High
	Band4 Type=Peaking
0dB
	Band1 Type=Shelving Low
–Gain	Band1 Type=Peaking
	3dB
	Band1 Cutoff	Band4 Cutoff

Effect

167