Korg Electric Keyboard manual 216, Amp LFO 1/2 Intensity Prog 5.1-2b, Pan Prog 5.1-1b

Amp LFO 1/2 Intensity (PROG 5.1–2b, 5.2)

The amp modulation intensity of LFO 1/2 can be controlled by EG, keyboard tracking, controllers, or tempo etc.

•If you select EG as the “AMS (LFO1/2 AMS),” the depth of the tremolo effect produced by LFO modulation will change in synchronization with the changes in EG level. If you set “Int. (AMS Intensity)” to a positive (+) value, the tremolo effect will deepen as the EG level rises, and lessen as the EG level falls. If “Int. (AMS Intensity)” is set to a negative (–)value, the phase of the LFO will be inverted.

•If select a controller such as SW1 or 2 as the “AMS (LFO1/2 AMS),” you can apply the tremolo effect by pressing the [SW1]or [SW2] key when desired.

Pan (PROG 5.1–1b)

The oscillator pan can be controlled by EG, LFO, keyboard tracking, controllers, or tempo etc.

•If you select Note No. as the “AMS (Pan AMS)” and set “Intensity” to +50, panning will be controlled by the keyboard position: center at the C4 note, far right at C6 or above, and far left at C2 or below.

•If EG is selected as the “AMS (Pan AMS),” the oscillator pan will be controlled in synchronization with the changes in EG level. If “Intensity” is set to a positive (+) value, the pan will move toward the right as the EG level increases, and toward the left as the EG level decreases. If “Intensity” is set to a negative (–)value, the opposite effect will occur.

EG Level – Pitch EG (PROG 3.1–5b)

–Filter EG (PROG 4.1–5b)

–Amp EG (PROG 5.1–3b)

EG levels can be controlled by keyboard tracking, control- lers, or tempo etc.

Set the “I (AMS Intensity)” value, and select +/–/0for each EG segment (“S” start, “A” attack, “B” break) to specify the direction of the effect (if any) on that segment.

+: AMS will function according to the Intensity setting.

–:The sign of the Intensity setting will be inverted.

0:AMS will have no effect.

If “I (AMS Intensity)” is set to +66, the various EG levels can be controlled over a maximum range of ±99.

•Set “AMS” to Velocity for Amp EG Level Modulation, “I (AMS Intensity)” to +66, “S” to 0, “A” to +, and “B” to –. Set all Amp EG levels to +00. As you play with increasing velocity, the EG levels will change more greatly. At the maximum velocity, the Start Level will stay at +00, but the Attack Level will change to +99 and the Break Level will change to –99.

EG Time – Pitch EG (PROG 3.1–5c)

–Filter EG (PROG 4.1–5c)

–Amp EG (PROG 5.1–3c)

EG times can be controlled by keyboard tracking, control- lers, or tempo etc. Set the “I (AMS Intensity)” value, and select +/–/0for each EG segment (“A” attack, D” decay, “S” slope, “R” release) to specify the direction of the effect (if any) on that segment.

+: AMS will function according to the Intensity setting.

–:The sign of the Intensity setting will be inverted.

0:AMS will have no effect.

Each EG time is determined by the Alternate Modulation value at the moment that the corresponding EG point is reached. For example, the Alternate Modulation value at the moment that the Attack Level is reached will determine the Decay Time.

If “I (AMS Intensity)” is set to a value of 8, 17, 25, 33, 41, or 49, the corresponding time can be multiplied by a maximum of 2, 4, 8, 16, 32, or 64 times (or divided by 1/2, 1/4, 1/8, 1/ 16, 1/32, 1/64).

•Select JS+Y#01 for “AMS,” and set “I (AMS Intensity)” to +8, “A” to +, “D” to –, and “S” and “R” to 0. When you move the joystick in the +Y direction, the Attack Time will be lengthened by a maximum of 2 times. The Decay Time will be shortened by a maximum of 1/2. The Slope and Release times will not change.

LFO Frequency (PROG 5.3–1b)

The frequency of LFO 1 or 2 can be controlled by EG, key- board tracking, controllers, or tempo etc., You can even use the LFO2 frequency to modulate the LFO1 frequency.

If “Int (AMS 1/2 Intensity)” is set to a value of 16, 33, 49, 66, 82, or 99, the corresponding frequency can be multiplied by a maximum of 2, 4, 8, 16, 32, or 64 times (or divided by 1/2, 1/4, 1/8, 1/16, 1/32, 1/64).

•Select JS+Y#01 for “AMS1/2 (Freq. AMS1/2),” and set “Int (AMS1/2 Intensity)” to +16. When you move the joystick in the +Y direction, the LFO frequency will be increased by a maximum of 2 times. If you set “Int (AMS1/2 Intensity)” to –16and move the joystick in the +Y direction, the LFO frequency will be decreased by up to 1/2.

216