Korg Electric Keyboard manual 123, 1c Auto Arp. Auto Arpeggiator

MFX1 Off [Off, On]

On (checked): MFX1 will be disabled.

Off (unchecked): The Master Effect Setup page (7.2–1) “MFX1 On/Off” settings of Program, Combination, and Sequencer mode will be valid.

MFX2 Off [Off, On]

On (checked): MFX2 will be disabled.

Off (unchecked): The Master Effect Setup page (7.2–1) “MFX2 On/Off” settings of Program, Combination, and Sequencer modes will be valid.

When “IFX On/Off,” or “MFX1 On/Off,” “MFX2 On/ Off” settings are switched, control change messages CC#92 (effect control 2), CC#94 (effect control 4), and CC#95 (effect control 5) will be transmitted respectively. The transmitted data will be 0 for off, and 127 for on.

1.1–1c: Auto Arp. (Auto Arpeggiator)

Program (Auto Arp. Program) [Off, On]

On (checked): When a different program is selected, the arpeggiator settings stored in that program will automati- cally take effect.

Off (unchecked): The arpeggiator settings will not change when the program is switched. Use this setting when you wish to keep the same arpeggiator pattern running while you select different program sounds.

Combi (Auto Arp. Combi) [Off, On]

On (checked): When a different combination is selected, the arpeggiator settings stored in that combination will auto- matically take effect.

Off (unchecked): The arpeggiator settings will not change when the combination is switched. Use this setting when you wish to keep the same arpeggiator pattern running while you select different combination sounds.

■1.1–1d: UTILITY

For details on how to select the desired utility function, refer to “PROG 1.1–1c: UTILITY.”

Write Global Setting

This command writes Global mode settings (except for Drum Kits and User Arpeggio Patterns).

1Select “Write Global Setting” to access the dialog box.

2To write the data, press the [F8] (“OK”) key. To cancel without writing, press the [F7] (“Cancel”) key.

You can also use the [REC/WRITE] key to write data in the same way as the “Write Global Setting” command. Press the [REC/WRITE] key to access the “Update Glo- bal Setting” dialog box, and press the [F8] key to write the data.

To write a drum kit or user arpeggio pattern, execute the appropriate utility. (☞ 5.1–1d “Write Drum Kits,” 6.1–1d “Write Arpeggio Patterns”)

Load Preload/Demo Data

This command loads the preloaded data and demo song data into internal memory. (☞ VNL)

Before loading this data, you must uncheck the “Mem- ory Protect” (1.1–2b) setting for the data that you want to load. If the setting is still checked when you attempt to load the data, a dialog box will indicate “Memory Protected,” and it will not be possible to load the data.

1Select “Load Preload/Demo Data,” and access the dialog box.

2In the “Kind” field, select the data that you want to load.

All (Preload PCG and	All PCG (programs, combinations, drum
Demo Songs)	kits, user arpeggio patterns, global set-
	tings), and demo song data
All Preload PCG	All PCG (programs, combinations, drum
	kits, user arpeggio patterns, global set-
	tings) data
All Demo Songs	All demo song data
Program All	All program data
Program Bank	All program data of a bank
Program Single	Data for one selected program
Combination All	All combination data
Combination Bank	All combination data of a bank
Combination Single	Data for one selected combination
DrumKit All	All drum kit data
DrumKit Single	Data for one selected drum kit
Arpeggio Pattern All	All arpeggio pattern data
Arpeggio Pattern Single	Data for one selected arpeggio pattern
Global Setting	Global setting data

If you selected Program or Combination, move the cur- sor down and select All, Bank, or Single to specify the range of data that will be loaded.

All: Data for all programs or combinations will be loaded.

Bank: Data will be loaded in units of one bank. In this case, move the cursor down and select the bank whose data you want to load.

Single: Data for one program or combination will be loaded. In this case, move the cursor down to select the data that you want to load.

If you selected DrumKit or Arpeggio Pattern, move the cursor down and select either All or Single to specify the range of data that will be loaded.

All: Data for all drum kits or arpeggio patterns will be loaded.

Single: Data for one drum kit or arpeggio pattern will be loaded. In this case, move the cursor down to select the data that you want to load.

3If you are loading in units of Bank or Single, use the “To” field to select the loading destination.

4To load the data, press the [F8] (“OK”) key. To cancel without loading, press the [F7] (“Cancel”) key.

6.1 5.1 4.1 3.1 2.1 1.1 GLOBAL

123