Korg Electric Keyboard manual Combi 2.2 Ed-Ctrl, Combi 3.1 Ed-Param1, Midi

COMBI 2.2: Ed–Ctrl

Here you can set the Combination mode functions of the B- mode functions of REALTIME CONTROLS knobs [1]–[4], and [SW1] key, [SW2] key.

2.2–1: Ctrls (Controls)

2.2–1a

2.2–1b2.2–1c

2.2–1a: Knob B Assign

These settings assign functions (mainly various control changes) to the B-mode of the REALTIME CONTROLS knobs [1]–[4] (☞ p.221 “Realtime Control Knobs B Assign List”).

The functions you specify here will be controlled when you operate the REALTIME CONTROLS knobs [1]–[4] in B- mode.

Since the REALTIME CONTROLS knob [1]–[4] function of the B-mode assignments made for the programs assigned to each timbre are not valid for the combination, new functions must be set by these parameters.

Knob1–B (Knob1–B Assign)	...[Off	MIDI CC#95]
Knob2–B (Knob2–B Assign)	[Off	MIDI CC#95]
Knob3–B (Knob3–B Assign)	[Off	MIDI CC#95]
Knob4–B (Knob4–B Assign)	[Off	MIDI CC#95]

2.2–1b: SW1/2 Assign

These settings assign the function of the [SW1] key and [SW2] key (☞ p.220 “SW1, SW2 Assign List”).

Since the function assignments of the [SW1] key and [SW2] key made for the programs assigned to each timbre are not valid for the combination, new functions must be set by these parameters.

SW1 (SW1 Assign)	[Off...AfterT Lock]
SW1 Mode	[Toggle, Momentary]
SW2 (SW2 Assign)	[Off...AfterT Lock]
SW2 Mode	[Toggle, Momentary]
(☞ PROG 2.2–1b)

■2.2–1c: UTILITY

☞“Write Combination,” “Solo Selected Timbre” (1.1–1c)

COMBI 3.1: Ed–Param1

3.1–1: MIDI

Here you can make MIDI settings for each timbre.

3.1–1a

3.1–1b

3.1–1a: Status, MIDI Channel, Bank(EX2) MSB/LSB

Status [INT, Off, EXT, EX2]

Specifies the status of MIDI and the internal tone generator for each timbre.

INT: When you play this instrument, the internal tone gen- erator will sound, and will also sound in respond to MIDI messages received from an external MIDI device.

Off: The program will not sound. Nor will MIDI data be transmitted.

EXT: Playing this instrument will not cause it to sound, but it will transmit data via MIDI to control external MIDI devices.

EX2: “Bank (EX2) MSB” and “Bank (EX2) LSB” (3.1–1a) will be enabled. Instead of the bank numbers for A–G(d) that can be selected on this instrument, the bank numbers you spec- ify here will be transmitted via MIDI. In other respects this is the same as EXT.

INT	MIDI IN
	Tone
	generator

EXT, EX2

MIDI OUT

MIDI Channel [01...16, Gch]

Set the MIDI transmit/receive channel for each timbre 1–8.

Gch: The timbre will use the channel that has been selected as the global MIDI channel “MIDI Channel” (GLOBAL 2.1– 1a).

When “Status” is INT, MIDI messages will be received on the channel you specify here. If this setting is the same as the global MIDI channel, the internal tone generator will sound according to the internal settings. If this is set to EXT or EX2, playing this instrument will transmit MIDI messages on the MIDI channel specified here. (Messages will also be trans- mitted simultaneously on the global MIDI channel.)

Bank(EX2)	MSB	[000:000...	127:127]
Bank(EX2)	LSB	[000:000...	127:127]

Specifies the bank number that will be transmitted when “Status” is set to EX2. If “Status” is not set to EX2, this set- ting has no effect.

■3.1–1b: UTILITY

☞“Write Combination,” “Solo Selected Timbre” (1.1–1c)

36