Korg Electric Keyboard manual 28 St.AutoFd Mod, 29 2Voice Reso, 179, Stereo Auto Fade Modulation

“LFO Freq Mod”=AUTOFADE, “(Amount)”=+3.00

The effect is off when a value for the dynamic modulation source specified for the “AUTOFADE Src” parameter is smaller than 64, and the effect is on when the value is 64 or higher. The AutoFade function is triggered when the value changes from 63 or smaller to 64 or higher.

AUTOFADE AutoFade

AUTOFADE Src=Gate1

LFO Frequency[Hz]=1.00

Gate1 SignalLFO Freq. Mod=AUTOFADE

Amt=+3.00

	Note On		All Note Off
		Fade-In Rate		LFO Frequency
AUTOFADE				=1.0+3.0=4.0Hz
	Fade-In Dealy
				LFO Frequency
				=1.0Hz

28: St.AutoFd Mod

(Stereo Auto Fade Modulation)

This stereo chorus/flanger effect enables you to control the LFO speed and effect balance using auto fade, and you can spread the sound by offsetting the phase of the left and right LFOs from each other.

Stereo In - Stereo Out
Left	Wet / Dry
	Delay
	Feedback
	High Damp
	Delay
Right	Wet / Dry
	LFO Phase
LFO: Tri / Sine	LFO Shape
AutoFade	LFO Frequency
	Wet / Dry

	LFO Wave (LFO Waveform)		Tri, Sine
a	Selects LFO Waveform
	Shape (LFO Shape)	–100...+100
	Determines how much the LFO waveform is changed		☞ Fx:20
b	LFO Phase	–180...+180deg
	Sets the LFO phase difference between the left and right		☞ Fx:10
	Freq (LFO Frequency)	0.02...20.00Hz
	Sets the LFO speed
c	(Source)		Off...Tempo
	Selects the modulation source of LFO speed
	(Amount)	–20.00...+20.00Hz
	Sets the modulation amount of LFO speed
	L Dly (L Pre Delay)	0.0...500.0ms
d	Sets the left channel delay time
	R Dly (R Pre Delay)	0.0...500.0ms
	Sets the right channel delay time
	Dep (Depth)		0...200
	Sets the depth of LFO modulation
e	Fb (Feedback)	–100...+100
	Sets the feedback amount		☞ Fx:20
	HD (High Damp)		0...100%
	Sets the feedback damping amount in the high range		☞ Fx:20
	AUTOFADE Src (AUTOFADE Source)		Off...Tempo

fSelects the modulation source that starts AutoFade

☞Fx:27,

	Fade Rate (Fade-In Rate)	1...100
g	Sets the rate of fade-in	☞ Fx:27
	Dly (Fade-In Delay)	00...2000ms
	Sets the fade-in delay time	☞ Fx:27
	Freq Mod (LFO Frequency Mod)	D-mod, AUTOFADE
h Switches between D-mod and AUTOFADE for the LFO frequency
	modulation	☞ Fx:27

	W/D Mod (Wet/Dry Mod)	D-mod, AUTOFADE
i	Switches between D-mod and AUTOFADE for the effect balance
	modulation	☞ Fx:27
	W/D (Wet/Dly)	–Wet...–1:99, Dry, 1:99...Wet
	Sets the balance between the effect and dry sounds
		☞ Fx:10, 20,
j	(Source)	Off...Tempo
	Selects the modulation source of the effect balance
	(Amount)	–100...+100
	Sets the modulation amount of the effect balance

29: 2Voice Reso

(2Voice Resonator)

This effect resonates the input signal at a specified pitch. You can set the pitch, output level, and pan settings for two reso- nators individually. You can control the resonance intensity via an LFO.

Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left			Wet / Dry
	High Damp
Trim	Resonator	Level	Pan
+	Resonance
Trim	Resonator	Level	Pan
	High Damp
Right			Wet / Dry
D-mod	Invert: On/Off
LFO	Pitch, Fine [cent]
	Control Mode
Manual

	Ctrl (Control Mode)	Manual, LFO, Dmod
a	Switches the controls of resonance intensity	☞ ,
	Invert (LFO/Dmod Invert)	Off, On
	Reverses the Voice 1 and 2 control when LFO/Dmod is selected		☞
	lfoF (LFO Frequency)	0.02...20.00Hz
b	Sets the LFO speed
	Dmod (Dmod Source)	Off...Tempo
	Selects the modulation source that controls resonance intensity
	Mod Dep (Mod Depth)	–100...+100
c	Sets the amount of resonance intensity control via LFO/Dmod
	Trim	0...100
	Sets the input level at the resonator
	V1 Pitch (Voice1 Pitch)	C0...B8
d	Sets the voice1 Pitch for resonance
	Fine	–50...+50cent
	Fine-adjusts the voice 1 pitch for resonance
	V1 Reso (Voice1 Resonance)	–100...+100
e	Sets the intensity of resonance when Control Mode = Manual		☞
	HiDamp (High Damp)	0...100%
	Sets the damping amount of resonant sound in the high range		☞
	V1 Level (Voice1 Level)	0...100
f	Sets the Voice1 output level
	Pan	L6...R6
	Sets the Voice1 stereo image
	V2 Pitch (Voice2 Pitch)	C0...B8
g	Sets the Voice2 Pitch for resonance
	Fine	–50...+50cent
	Fine-adjusts the voice 2 pitch for resonance
	V2 Reso (Voice2 Resonance)	–100...+100
h	Sets the intensity of resonance when Control Mode = Manual		☞
	HiDamp (High Damp)	0...100%
	Sets the damping amount of resonant sound in the high range		☞
	V2 Level (Voice2 Level)	0...100
i	Sets the Voice2 output level
	Pan	L6...R6
	Sets the Voice2 stereo image

Effect

179