Minelab P0591-A, Mine lab Explorer IITM Recharging NiMH battery pack with the car charger

Page 34

www.minelab.com

THE MINELAB EXPLORER II

34

Recharging

$

Minelab’s battery chargers are suitable for the Explorer NiMH battery pack only. The battery chargers will not recharge rechargeable alkaline batteries. Using

anon-Minelab charger with the battery pack may damage it and will void the product warranty.

Recharging NiMH battery pack with the car charger

The Explorer II is provided with a car charger that boosts the voltage of the car battery (usually about 12V) to a voltage sufficiently high to charge the NiMH battery pack.

STEP 1 Remove battery pack as per instructions on page 24.

STEP 2 Insert the car charger plug into the cigarette lighter socket.

STEP 3 Insert the car charger plug into the socket at the tapered end of the battery pack. A small light on the car charger illuminates indicating that the car charger is in operation.

NOTE Some vehicles will need the ignition to be switched on

to ‘accessories’ for power to be supplied to the charger.

STEP 4 Leave the battery to charge for about 18 hours for a complete recharge. If the battery was not completely discharged, the charging time will be shorter.

The car charger is provided with a 3AG 2Amp fast fuse for short circuit protection that can be accessed by unscrewing the tip of the cigarette lighter plug.

NOTE Charging the battery beyond full capacity will not damage the NiMH battery pack, but it could gradually discharge your car battery.

THE BATTERY PACK

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Minelab Explorer Minelab Explorer Contents Table of Contents contents Minelab Explorer User Info Introduction Soon as you have assembled the detectorAbout this Manual Minelab Electronics wish you every success in your treasure HuntingAdvanced mode Two mode detectingQuickstart mode MINELAB’S Unique TechnologyAdvanced Use provides all of the information you need to Getting Lost?Personalize your Explorer for specialized targeting Discrimination Full Band Spectrum FBSYou are now ready to proceed to Assembly Ground CompensationMinelab Explorer Assembly Easy reference Unpacking Your ExplorerList of Parts AccessoriesYou can also visit us on the web Handle assembly Shaft assembly Search coil Assembling the DetectorDetector warranty Connecting the search coil to the lower shaftWhere it enters the search coil itself. They are shipped Pre-assembled and any attempt to disconnect will void yourYou are now ready to proceed to the shaft assembly Securing yoke to search coilTo assemble the lower and upper shaft Shaft assemblyLower shaft Connecting the shaft assembly to the handle assembly Connecting the Shaft AssemblyShaft You are now ready to proceed to the handle assembly Coil not connected?Adjusting the armrest assembly Handle AssemblyTo adjust armrest Fitting the armrest strap Headphones Attaching headphonesRubber Washer Replacing and Fitting the Search Coil Control Panel Easy reference Control PanelBatteries Removal of battery pack Battery PackReplacing alkaline batteries Charger Recharging NiMH battery pack with the mainsNiMH battery pack supplied with your detector It as explained below before operating the detector.To ‘accessories’ for power to be supplied to the charger Recharging NiMH battery pack with the car chargerRecharging Hours Battery life indicationsYou are now ready to proceed to Control Panel Control Panel Quickstart Display memory Getting StartedIntroducing Quickstart Beginner USE Trying out the detectorQuickstart Display 10 2Areas of the screen are Smartfind’s preset Two-dimensional discrimination explained Two-dimensional discriminationQUICKSTART’S Smartfind Display Conductivity Ferrous contentInterpreting target responses Items will cause the target crosshair to appear at the topIntroducing Discrim Smartfind Discrimination patternAdjusting the Iron Mask Iron MaskOperating in Iron Mask Smartfind in Iron MaskDigital display Target crosshair displayed in Smartfind mode that is, itsQUICKSTART’S Digital Display Ferrous and conductivity ratingModifying the Display Adjusting the display contrastFull screen display Sensitivity control Noise CancelAdjusting sensitivity Semi-autoDisplay Icon Adjusting ThresholdThreshold control Audio Response Adjusting the volumePitch of response Introduction to the Audio menu HeadphonesAudio Menu Main Menu AudioIntroducing Volume Audio Adjusting the VolumeMax limit Main Menu Audio Volume Gain adjustment GainVariability Introducing ToneThreshold tone LimitsConstant Audio Adjusting the SoundsIntroducing Sounds ConductivityFerrous Main Menu Audio Sounds FerrousTesting Target Audio Responses tutorial Rusty nail buried nearby. Selection of Pinpoint instructs Introducing PinpointExplorer II’s Pinpoint function Respond to the nailUsing Pinpoint 21 Pinpointing the objectFill your holes Selecting Targets Select targets listSmartfind thumbnail. Discrimination pattern for current Mask shortcut button Explorer’s II Discrim factory settingTop left corner of all discrimination patterns Main Menu Options Advanced Moving to Advanced modeReset the detector You are now ready to proceed to Advanced UseMinelab Explorer Advanced Use Advanced MODE’S Main Menu Audio menu. SeeBeginning Advanced use Starting in Advanced ModeAre you ready? Advanced target preferencesAdvanced MODE’S Displays Advanced MODE’S Learn Display Introducing Learn Learning TargetsSilence please Explorer II’s Discrimination functionsAdjustments and save your selection Phase 1 Preparation for LearnThis tutorial shows you how to learn a target, make LEARN’S Target SelectionPhase 2 Learning and Saving the target pattern For more detail on Save DISCRIM, turn toAdvanced MODE’S Edit Display Main Menu Display Edit Editing PatternsIntroducing Edit Edit to customize your discrimination patternPhase 2 Resizing and moving the target frame Phase 1 Preparing for editingEditing and Saving Target Patterns Phase 4 Saving edited discrimination pattern Phase 3 Rejecting the framed target areaSelect menu as Advanced mode’s current setting Advanced mode’s Select menu Advanced MODE’S Select MenuMain Menu Select Saving targets Saving TargetsSaving Shortcut Main Menu Save Save Discrim S1-S6Volume Shortcut Audio menuOptions menu Options MenuMain Menu Options Noise Options NoiseNoise Shortcut Main Menu Options NoiseMain Menu Options Response Options ResponseIntroducing Response NormalAudio Main Menu Options Recovery Options RecoveryIntroducing Recovery FastSaving and loading a setting Settings MenuIntroducing the Settings menu Main Menu Options SettingsGet into the habit As mentioned earlier in thisUser Info Batteries Noise Cancel Helpful Hints user tipsMinelab Explorer Battery Performance Comparisons Setting Range Factory Preset User a User B User PreferencesUser Preferences Control Panel Button Functions Quickstart Menu Structure Advanced Menu Structure Start at all Switches off by itselfDetector does not Detector starts, but itPurchased From Service Repair FormDescription of Fault Phone100 Warranty RepairsTechnical Specifications for the Minelab Explorer Explorer II Model User Functions SoftwareGlossary of Terms 105 106 107 Detector Care and Safety take care

Mine lab Explorer IITM, P0591-A specifications

The Minelab P0591-A, commonly known as the Explorer II, is an advanced metal detector that appeals to hobbyists and professionals alike. Renowned for its cutting-edge technology and robust features, the Explorer II sets a high standard for metal detecting equipment.

One of the standout features of the Explorer II is its Multi-Frequency Technology. This groundbreaking system allows the detector to operate on multiple frequencies simultaneously, enhancing its ability to detect a wide range of metal objects. This versatility means users can efficiently find everything from small coins to larger artifacts, all while minimizing the risk of missing valuable targets.

The Explorer II is also equipped with Smartfind discrimination technology. This feature provides users with a visual representation of the detected signals, allowing them to distinguish between different types of metals. The LCD screen displays a target ID, enabling the detectorist to make informed decisions about whether to dig or not based on the target’s identity. This capability not only saves time but also enhances the overall efficiency of treasure hunting.

Another significant characteristic of the Explorer II is its customizable settings. The detector comes with various pre-set detecting modes for different environments, such as trashy urban areas or open fields rich in history. Users can also manipulate sensitivity settings and discrimination levels, tailoring the device to their specific needs and preferences. This level of customization makes the Explorer II a versatile tool suitable for various terrains and conditions.

The build quality of the Explorer II is also commendable. Designed for durability, it can withstand the rigors of outdoor use while remaining lightweight and user-friendly. The adjustable shaft allows for comfortable use for users of all heights, and the ergonomic design ensures that long treasure hunting sessions are less fatiguing.

Battery life is another area where the Explorer II excels. The device operates on a rechargeable battery, providing extended use without the need for frequent changes. This capacity for prolonged operation makes it ideal for long days out in the field.

In summary, the Minelab P0591-A Explorer II is a sophisticated metal detector that combines innovative technology with user-friendly features. Its Multi-Frequency Technology, Smartfind discrimination, customization options, and durable build make it a top choice for those serious about metal detecting. Whether searching for coins in local parks or exploring historical sites, the Explorer II provides users with the tools necessary for a successful treasure hunting experience.
Top Page Image Contents