Land Pride RCSM3596, RCS3510 Flex Couplers, Tractor Maintenance, Storage, Skid Shoe Maintenance

Page 22

Table of Contents

Section 4: Maintenance and Lubrication

Land Pride

Flex Couplers

Refer to Figure 4-5:

Replace two rubber discs (#1) (Land Pride Part No. 1785273) as follows: Refer to land Pride’s Parts Manual 312-708P if additional repair parts are required.

1.Insert three bolts (#3) through the holes in flange weldment (#7).

2.Place beaded washers (#2) over the three bolts with bead facing rubber disc (#1).

3.Place bushings (#6), rubber disc (#1), washers (#5), 2nd rubber disc (#1), 2nd bushing (#6) and 2nd washer (5) over the three bolts as shown.

4.Secure with nuts (#4). Do not tighten.

5.Insert three bolts (#3) through the holes in flanged hub (#8).

6.Repeat steps 2 through 4.

7.Tighten nuts (#4) evenly with nuts torqued 35 to

40 ft-lb. Beaded washers (#2) should be imbedded halfway into the rubber disc.

14560

Flex Couplers

Figure 4-5

4. Repeat on opposite side.

Land Pride Skid Shoe Replacement Parts

Part No.

Part Description

312-602D

SKID SHOE

802-466C

PLOW 3/8” - 16 x 1 1/4” GR5

803-198C

NUT HEX WHIZ 3/8-16 PLT

 

22454

Skid Shoe Replacement

Figure 4-6

Tractor Maintenance

One of the most important things you can do to prevent hydraulic system problems is to ensure that your tractor's reservoir remains free of dirt and contamination.

Use a clean cloth to wipe the hose ends before attaching them to your tractor. Replace the filter element for your tractor’s hydraulic system at the prescribed intervals.

These simple maintenances will go a long way to prevent the occurrence of cartridge valve and hydraulic cylinder problems on the Rotary Cutter.

Storage

At the end of the working season or when the cutter will not be used for a long period, it is good practice to clean off any dirt or grease that may have accumulated on the cutter and any of the moving parts.

Skid Shoe Maintenance

!WARNING!

Excessive wear on skid shoes may cause inadequate operation of cutter and create a safety hazard!

There are two skid shoes mounted on the cutter sides. Check both skid shoes for wear and replace if necessary. Order only genuine Land Pride parts from your local Land Pride Dealer.

Refer to Figure 4-6:

1.Remove 3/8" hex whiz nuts (#3), 3/8" plow bolts (#2) and skid shoe (#1) as shown.

2.Plow bolts should be checked for wear and replaced if necessary.

3.Attach new skid shoe (#1) to cutter with existing 3/8” plow bolts (#2) and secure with 3/8" hex whiz nuts. Torque to 31 ft. lbs.

1. Clean the cutter as necessary.

2.Check the blades for wear and replace if necessary, see “Service Cutting Blades”, Page 18.

3.Inspect the cutter for loose, damaged or worn parts and adjust or replace as needed.

4.Lubricate as noted in “Lubrication”, page 21.

5.Store the cutter inside if possible for longer cutter life.

6.Repaint parts where paint is worn or scratched to prevent rust. Ask your dealer for Aerosol Land Pride touch-up paint.

Land Pride Touch-up Paints

Part No.

Part Description

821-011C PAINT LP BEIGE SPRAY CAN

821-002C PAINT GP BLACK SPRAY CAN

821-054C PAINT MEDIUM RED SPRAY CAN

821-058C PAINT GREEN SPRAY CAN

20 RCS3596, RCSM3596, RCS3510 & RCSM3510 Series Rotary Cutters 312-708M

6/26/06

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Rotary Cutters Table of Contents For Your Protection Important Safety InformationBe Aware Signal Words Shutdown and StorageTransport Machinery Safely Use a Safety ChainPractice Safe Mainte- nance Keep Riders Off Machinery Wear Protective EquipmentAvoid High Pressure Fluids Hazard 818-130C Shown 818-240C 818-229C 818-230C818-543C 818-552C 818-556C818-142C 818-564C838-094C 818-540C 818-552COwner Assistance Using This ManualApplication IntroductionTractor Requirements Pre-Assembly ChecklistAssembly and Set-Up Dealer PreparationsTailwheel Assembly Hitch AssemblyDriveline Installation Front Chain Guards Safety Guards OptionalFront Rubber Guards Rear Chain GuardsPTO Hook-up Vent Plug InstallationTractor Hook-Up Un-Hooking from the Tractor Hydraulic Hook-UpAdjustments Leveling ProcedureCutter Height Adjustment Minimum Cutting HeightTransporting Operating ChecklistOperating Check List Offset FunctionDitch / Bank Cutting InstructionsCrossing Steep Ditches & Banks RightGeneral Operating Instructions Maintenance and Lubrication MaintenanceService Cutting Blades Land Pride Cutter Blade PartsDriveline Clutch Clutch Assembly and DisassemblyClutch Run-In Flex Couplers Tractor MaintenanceSkid Shoe Maintenance StorageTailwheel Spindle Tube LubricationHours Tailwheel HubDriveline U-Joints Offset ArmsDriveline Flex Coupler Ratchet JackSpecifications & Capacities RCSM3596 & RCSM3510 SeriesFeatures and Benefits Features BenefitsTroubleshooting Problem Cause Solution Oil seal leakingProblem Cause Solution Excessive vibration Torque Values Chart for Common Bolt Sizes AppendixWarranty Corporate Office P.O. Box Salina, Kansas 67402-5060 USA
Related manuals
Manual 52 pages 58.67 Kb

RCSM3510, RCSM3596, RCS3596, RCS3510 specifications

Land Pride is a leading manufacturer of agricultural and landscaping equipment, known for its dedication to quality and innovation. Among its impressive lineup are the RCS3510, RCS3596, RCSM3596, and RCSM3510 rotary cutters, specifically engineered to meet the diverse demands of land clearing and maintenance.

Starting with the RCS3510, this model features a cutting width of 10 feet, making it ideal for larger areas that require efficient vegetation management. Its robust design incorporates a 1/4-inch steel deck for enhanced durability and ruggedness under various terrain conditions. This model offers adjustable skids that enable operators to manage cutting height effectively, ensuring an optimal finish on different surfaces.

Next, the RCS3596 delivers a slightly larger cutting width of 96 inches, making it perfect for commercial applications. It is built with a heavy-duty frame and offers a reinforced steel deck that withstands harsh conditions. The RCS3596 is equipped with a cutting mechanism that utilizes dual-blade technology, ensuring a cleaner cut and more efficient operation. The quick-attach hitch system also enhances productivity by enabling fast and easy attachment to various tractors.

For those who require a more compact solution, the RCSM3596 and RCSM3510 models offer a slimmed-down approach without compromising performance. The RCSM3596 has a cutting width of 96 inches, and its high-strength gearboxes ensure reliable power transfer and longevity. This model has a unique feature where the winged design allows for easy maneuverability in tight spaces while still providing excellent cutting capabilities.

The RCSM3510 features a 10-foot cutting width with a lightweight structure that maximizes tractor efficiency. Both RCSM models come with a low-profile design, allowing for optimal visibility and precision during operation. In terms of safety, all four models incorporate shielded gearboxes and safety features that protect the operator and enhance overall job site safety.

In conclusion, the Land Pride RCS3510, RCS3596, RCSM3596, and RCSM3510 rotary cutters represent a blend of performance, durability, and advanced technologies that meet the needs of modern land management. With their heavy-duty construction, innovative designs, and user-friendly features, these models stand out in the competitive market, delivering exceptional value to operators seeking reliable and efficient cutting solutions. Whether managing large fields or navigating tight spaces, Land Pride rotary cutters are engineered to excel in any task.
Top Page Image Contents