Land Pride RCSM3510, RCS3510 Tractor Requirements, Dealer Preparations, Pre-Assembly Checklist

Page 11

Land Pride

Table of Contents

Section 1: Assembly and Set-Up

Tractor Requirements

Weight & Horsepower

Tractor horsepower and weight must be capable of controlling the cutter under all operating conditions. Tractors outside the horsepower range must not be used.

•RCS3596 cutters & RCSM3596

Semi-Mount 30-120 HP

•RCS3510 & RCSM3510 cutters

Semi-Mount 50-120 HP

NOTE: Ballast may need to be added to your tractor to maintain steering control. Refer to your tractor’s operator manual to determine if one needs additional ballast.

PTO Type & Speed

Tractor’s rear power take-off (PTO) speed and spline type must be capable of matching the cutter’s PTO type and speed.

•RCS3596 and RCS3510 cutters

540RPM 1 3/8”-6 spline rear power take-off

•RCSM3596 and RCSM3510 cutters

1000 RPM 1 3/8”-21 spline rear power take-off

3-Point Hitch

The lower 3-Point arms of the 3-Point hitch must be stabilized to prevent side-to-side movement. Most tractors have sway blocks or adjustable chains for this purpose. Category of hitch is dependent upon the series of cutter being used.

•RCS3596 & RCSM3596 (Category l or ll hitch)

•RCS35510 & RCSM3510 (Category ll or lll hitch)

Dealer Preparations

Read and understand the operator’s manual for your cutter. An understanding of how it works will aid in the assembly and setup of your cutter.

This Rotary Cutter has been partially assembled at the factory. However, some assembly will be necessary to attach the hitch, driveline and guards to the cutter.

It is best to go through the Pre-Assembly Checklist before assembling the cutter. Speed up your assembly task and make the job safer by having all the needed parts and equipment readily at hand.

Pre-Assembly Checklist

Check

Reference

Fasteners and pins that were shipped

Operator’s

with the cutter. NOTE: All hardware from

Manual

the factory has been installed in the

 

location where it will be used. If a part or

 

fastener is temporarily removed for

 

assembly reasons, remember where it

 

goes.Keep the parts separated.

 

 

 

Be sure the parts get used in the correct

Operator’s

location. By double checking while you

Manual

assemble, you will lessen the chance of

 

using a bolt incorrectly that may be

 

needed later.

 

 

 

All grease fittings are in place and

Section 4

lubricated.

Page 21

 

 

Safety labels are correctly located and

Safety

legible. Replace if damaged.

Information

 

Page 1

 

 

Red and amber reflectors are correctly

Safety

located and visible when the cutter is in

Information

the transport position.

Page 1

 

 

Have a minimum of 2 people at hand

Operator’s

while assembling the cutter.

Manual

 

 

Have a fork lift or loader along with

Operator’s

chains and safety stands that are sized

Manual

for the job ready for the assembly task.

 

 

 

6/26/06

RCS3596, RCSM3596, RCS3510 & RCSM3510 Series Rotary Cutters 312-708M

9

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Rotary Cutters Table of Contents Shutdown and Storage Important Safety InformationBe Aware Signal Words For Your ProtectionPractice Safe Mainte- nance Use a Safety ChainTransport Machinery Safely Avoid High Pressure Fluids Hazard Wear Protective EquipmentKeep Riders Off Machinery 818-230C 818-130C Shown 818-240C 818-229C818-552C 818-556C 818-543C838-094C 818-564C818-142C 818-552C 818-540CIntroduction Using This ManualApplication Owner AssistanceDealer Preparations Pre-Assembly ChecklistAssembly and Set-Up Tractor RequirementsDriveline Installation Hitch AssemblyTailwheel Assembly Rear Chain Guards Safety Guards OptionalFront Rubber Guards Front Chain GuardsTractor Hook-Up Vent Plug InstallationPTO Hook-up Hydraulic Hook-Up Un-Hooking from the TractorMinimum Cutting Height Leveling ProcedureCutter Height Adjustment AdjustmentsOffset Function Operating ChecklistOperating Check List TransportingRight Cutting InstructionsCrossing Steep Ditches & Banks Ditch / BankGeneral Operating Instructions Land Pride Cutter Blade Parts MaintenanceService Cutting Blades Maintenance and LubricationClutch Run-In Clutch Assembly and DisassemblyDriveline Clutch Storage Tractor MaintenanceSkid Shoe Maintenance Flex CouplersTailwheel Hub LubricationHours Tailwheel Spindle TubeDriveline Offset ArmsDriveline U-Joints Ratchet Jack Flex CouplerRCSM3596 & RCSM3510 Series Specifications & CapacitiesFeatures Benefits Features and BenefitsProblem Cause Solution Oil seal leaking TroubleshootingProblem Cause Solution Excessive vibration Appendix Torque Values Chart for Common Bolt SizesWarranty Corporate Office P.O. Box Salina, Kansas 67402-5060 USA
Related manuals
Manual 52 pages 58.67 Kb

RCSM3510, RCSM3596, RCS3596, RCS3510 specifications

Land Pride is a leading manufacturer of agricultural and landscaping equipment, known for its dedication to quality and innovation. Among its impressive lineup are the RCS3510, RCS3596, RCSM3596, and RCSM3510 rotary cutters, specifically engineered to meet the diverse demands of land clearing and maintenance.

Starting with the RCS3510, this model features a cutting width of 10 feet, making it ideal for larger areas that require efficient vegetation management. Its robust design incorporates a 1/4-inch steel deck for enhanced durability and ruggedness under various terrain conditions. This model offers adjustable skids that enable operators to manage cutting height effectively, ensuring an optimal finish on different surfaces.

Next, the RCS3596 delivers a slightly larger cutting width of 96 inches, making it perfect for commercial applications. It is built with a heavy-duty frame and offers a reinforced steel deck that withstands harsh conditions. The RCS3596 is equipped with a cutting mechanism that utilizes dual-blade technology, ensuring a cleaner cut and more efficient operation. The quick-attach hitch system also enhances productivity by enabling fast and easy attachment to various tractors.

For those who require a more compact solution, the RCSM3596 and RCSM3510 models offer a slimmed-down approach without compromising performance. The RCSM3596 has a cutting width of 96 inches, and its high-strength gearboxes ensure reliable power transfer and longevity. This model has a unique feature where the winged design allows for easy maneuverability in tight spaces while still providing excellent cutting capabilities.

The RCSM3510 features a 10-foot cutting width with a lightweight structure that maximizes tractor efficiency. Both RCSM models come with a low-profile design, allowing for optimal visibility and precision during operation. In terms of safety, all four models incorporate shielded gearboxes and safety features that protect the operator and enhance overall job site safety.

In conclusion, the Land Pride RCS3510, RCS3596, RCSM3596, and RCSM3510 rotary cutters represent a blend of performance, durability, and advanced technologies that meet the needs of modern land management. With their heavy-duty construction, innovative designs, and user-friendly features, these models stand out in the competitive market, delivering exceptional value to operators seeking reliable and efficient cutting solutions. Whether managing large fields or navigating tight spaces, Land Pride rotary cutters are engineered to excel in any task.
Top Page Image Contents