Marantz SR7001, SR8001 manual Rear Panel, Multi Speaker / Speaker C, Output, 0AC Outlets, 1AC Inlet

ENGLISH	REAR PANEL
	q w e	r tyu		i
	INPUT 1(TV)	INPUT 2(DVD)
		OUT	SURROUND	SPEAKER
			MODEL NO. SR8001BACK	SYSTEMS
		PUT

yXM terminal

See page 19 for connecting information.

uSub Speaker outputs terminals

(MULTI SPEAKER / SPEAKER C)

Two terminals are provided for the front left, and right speakers for multi room.

The terminals can be used to connect a third set of

!2Preamp Outputs

(L, R, SL, SR, SBL, SBR, C)

Jacks for L (front left), R (front right), C (Center), SL (surround left), SR (surround right), SBL (surround back left) and SBR (surround back right).

Use these jacks for connection to external power amplifiers.

L

RS-232C

FM (75Ω)

GND

AM

ANTENNA

CB/PB

CR/PR

CB/PB

CR/PR

CB/PB

CR/PR

OUT

COMPONENT

Y

Y

Y

PUT

VIDEO

INPUT 3(VCR1)

INPUT 4(DSS/VCR2)

2

R

@4

INPUT 1(TV)

INPUT 2(DVD)

INPUT 3(VCR1) INPUT 4(DSS/VCR2)

OUTPUT 1

OUTPUT 2

HDMI

Ver1.2

L

XM

TV(1)

DVD(2)

VCR1(3)

DSS/VCR2(4) MONITOR MULTI

TV(1)

DVD(2)

VCR1(3)

DSS/VCR2(4)

MONI. OUT

AC IN

@3

OUT

OUT

R

VIDEO

IN

OUT

IN

OUT

IN

OUT

IN

OUT

S-VIDEO

DIGITAL IN

DIGITAL OUT

RC-5 MULTI RC

DC OUT

L

SL

SBL

C

MULTI SPEAKER ON

1

1

/SPEAKER C

OFF

@2

4

5

6

COAX.

IN

SUB SPEAKER

IR

FLASHER RECEIVER

PRE

IN

IN

OUT

UNSWITCHED

1

2

3

OPT.

2

2

1.25A 150W MAX

OUT

EMITTER

R

SR

SBR

SW

OUT

TV

DVD

VCR1

DSS/VCR2

TAPE

CD/CDR

MULTI OUT

L

SL

SBL

C

@1

L

R

7.1CH

IN

SWITCHED

IN

OUT

IN

OUT

IN

OUT

IN

OUT

A

B

1.25A 150W MAX

R

SR

SBR

SW

AC OUTLETS

AUDIO

(AUX2)

120V 60Hz

L

FRONT

A

R

L

FRONT

B

R

CEN

TER

L

SURR.

R

FRONT A OR B.CENTER.SURR. SURR BACK : MINIMUM 6 OHMS FRONT A + B : MINIMUM 8 OHMS

@0!9!8!7!6e!5!4 !3!2!1 !0o

qFM antenna terminal (75 ohms)

Connect an external FM antenna with a coaxial cable, or a cable network FM source.

AM antenna and ground terminals

Connect the supplied AM loop antenna. Use the terminals marked “AM” and “GND”. The supplied AM loop antenna will provide good AM reception in most areas. Position the loop antenna until you hear the best reception.

wCOMPONENT VIDEO INPUT/

OUTPUT

If your DVD player or other device has component video connectors, be sure to connect them to these component video connectors on the SR7001. The SR7001 has 4 component video input connectors to obtain the color information (Y, CB, CR) directly from the recorded DVD signal or other video component and two component video outputs connector to output it directly into the matrix decoder of the display device.

By sending the pure DVD component video signal directly, the DVD signal forgoes the extra processing that normally would degrade the image. The result is vastly increased image quality, with incredibly life like colors and crisp detail.

eMultiroom Outputs (Audio output

A/B, Video)

These are the audio and video output jacks for the Multi zone (Multi room).

Connect these jacks to optional audio power amplifiers or video display devices to listen and view the source selected by the multiroom system in a remote room.

rMONITOR OUT

These are monitor outputs and each one includes both composite video and S-video confi gurations. When connecting two video monitors or televisions, be aware that the OSD interface can be used with both MONITOR OUT connections.

tRS-232C

The RS-232C port is to be used in conjunction with an external controller to control the operation of the SR7001 by using an external device.

The RS-232C port may also be used in the future to update the operating software of the SR7001 so that it will be able to support new digital audio formats and the like as they are introduced.

speakers by setting the SPEAKER C selector switch to ON. For connection and use, see page 20.

iSpeaker outputs terminals

Nine terminals are provided for the front (A) left, front

(A)right, front (B) left, front (B) right, front center, surround left, surround right, surround back left and surround back right speakers.

!3Subwoofer Output

Connect this jack to the line level input of a powered subwoofer. If an external subwoofer amplifier is used, connect this jack to the subwoofer amplifi er input. If you are using two subwoofers, either powered or with a 2 channel subwoofer amplifier, connect a “Y” connector to the subwoofer output jack and run one cable from it to each subwoofer amplifier.

o SPEAKER C switch	!47.1 CHANNEL or AUX2 INPUT
	By connecting a DVD Audio player, Super Audio CD
Set to ON to connect a bi-amp to this receiver or set	multichannel player, or other components that has a
to OFF for normal speaker connection (surround	multichannel port, you can playback the audio with
back and multiroom speakers). (See page 20)	5.1 channel or 7.1 channel outputs.

!0AC OUTLETS

Connect the AC power cables of components such as a DVD and CD player to these outlets. SWITCHED and UNSWITCHED outlets are provided.

The one marked SWITCHED provides power only when the SR7001 is turned on and is useful for components which you use every time you play your system.

The one marked UNSWITCHED is always live as long as the SR7001 is plugged into a live outlet.

A component connected here may be left on permanently, or may be switched off with via its own power switch.

Caution:

•In order to avoid potential turn-off thumps, anything plugged into these outlets should be powered up before the SR7001 is turned on.

•The capacity of this AC outlet is 150W. Do not connect devices that consume electricity more than the capacity of these AC outlets. If the total power consumption of the connected devices exceeds the capacity, the protection circuit shuts down the power supply.

!5EMITTER OUT (SR8001 only)

The signals input to the IR RECEIVER IN terminals are output to this terminal. External devices can be controlled by connecting them to this terminal.

!6IR RECEIVER IN (SR8001 only)

Connect to an external IR receiver.

!7FLASHER IN (Flasher input terminal)

These terminals are to control the unit from each zone. Connect the control signal from a Keypad, etc.

!8DC TRIGGER output terminal

Connect a device that needs to be triggered by DC under certain conditions (screen, power strip, etc…) Use the system OSD setup menu to determine the conditions by which these jack will be active.

Note:

•This output voltage is for (status) control only, It is not sufficient for drive capability.

!1AC INLET

Plug the supplied power cord into this AC INLET and then into the power outlet on the wall.

SR7001 can be powered by 120V AC only.

!9MULTI ROOM REMOTE IN/OUT terminals

IN: Connect to a multi-room remote control device, available from your Marantz dealer.

OUT: Connect to the Marantz component equipped with remote control (RC-5) terminals in Multi zone (Multi room).

8