BASIC OPERATION |
SELECTING THE SURROUND MODE | ADJUSTING THE MAIN VOLUME |
ADJUSTING THE TONE (BASS & TREBLE)
CONTROL
ENGLISH | (PLAY BACK) | |
SELECTING AN INPUT SOURCE | ||
|
Before you can listen to any input media, you must first select the input source on the SR7001.
Example : DVD
AV SURROUND RECEIVER SR8001
TV DVD VCR DSS
TUNER | CD | MD | |
TAPE | AUX1 | AUX2 | AMP |
|
| LIGHT |
|
1 |
|
| 2 |
RC8001SR
Learning Remote Controller
To select DVD, turn the INPUT SELECTOR knob on the front panel or press the DVD button on the
Example: AUTO SURROUND
M
D1
D2
D3
D4
USEPAGE 1 2 3 4
D5
AV SURROUND RECEIVER SR8001
CHVOL
7.1CH |
| ATT | |
4 |
| 5 | 6 |
DISP |
| OSD | SLEEP |
7 |
| 8 | 9 |
CLEAR |
| 0 | MEMO |
TUNER | CD | MD | |
TAPE | AUX1 | AUX2 | AMP |
|
| LIGHT |
|
1 |
|
| 2 |
RC8001SR
Learning Remote Controller
CH |
| VOL |
SURROUND |
|
|
DIGITAL |
|
|
AAC |
|
|
| OK |
|
| LIP.SYNC |
|
PREV |
| MUTE |
| GUIDE |
|
MENU |
| EXIT |
TEST | CH.SEL | SURR |
1 | 2 | 3 |
7.1CH | ATT |
|
Adjust the volume to a comfortable level using the VOLUME control knob on the front panel or VOLUME 3 / 4 buttons on the remote.
To increase the volume, turn the VOLUME knob clockwise or press VOLUME 3 button on the remote, to decrease the volume, turn counterclockwise or press VOLUME 4 button on the remote.
Notes:
•The volume can be adjusted within the range of – ∞ to 18 dB, in steps of 1 dB.
M
D1
D2
D3
D4
USEPAGE 3
D5
CH | VOL |
TUNER CD |
TAPE | AUX1 | AUX2 | AMP |
|
| LIGHT |
|
1 |
|
| 2 |
RC8001SR
Learning Remote Controller
During a listening session you may wish to adjust the Bass and Treble Control to suit your listening tastes or room acoustics.
(Using the remote control unit)
To adjust the tone, press the AMP button and press the > button PAGE3 is displayed.
remote two times in a row. After you have selected DVD, simply turn on the DVD player and play the DVD.
• | As the input source is changed, the new input |
| name will appear momentarily an OSD information |
| on the video display. The input name will also |
| appear in the display, on the |
• | If you use the FUNCTION RENAME feature (see |
| page 26) , the renamed name appears on the |
| display. |
• As the input is changed, the SR7001 will | |
| automatically switch to the digital input, surround |
| mode, attenuation, and night mode status which |
| were entered during the configuration process for |
| that source. |
• | When an audio source is selected, the last video |
| input used remains routed to the VCR1 & DSS/ |
| VCR2 Outputs and Monitor Output. This permits |
| simultaneous viewing and listening to different |
| sources. |
• | When a video source is selected, the selected |
(Using the SR7001)
To select the Auto surround mode during playback, press the AUTO button on the front panel.
(Using the remote control unit)
To select the Auto surround mode, press the AMP button and press the > button until PAGE1 is displayed. Press the AUTO (D1) button.
•For surround modes, see “Surround Mode” on page 42.
•To add the THX mode to the Auto Surround mode, press either the THX button on the SR7001 or the THX button on the remote control unit.
•To select a specifi c surround mode, Press the individual surround mode button on page 1.2 on the remote control unit.
•However, when the channel level is set as described on page 33, if the volume for any channel is set at +1 dB or greater, the volume cannot be adjusted up to 18 dB.
(In this case the maximum volume adjustment range is “18 dB - Maximum value of channel level)
NIGHT MODE
M
D1
D2
D3
D4
USE | PAGE | 3 |
D5
CHVOL
TUNER | CD | MD | |
TAPE | AUX1 | AUX2 | AMP |
|
| LIGHT |
|
1 |
|
| 2 |
RC8001SR
Learning Remote Controller
To adjust the bass effect, press BASS+ (D2) or BASS– (D3).
To adjust the treble effect, TREB+ (D4) or TREB– (D5).
Notes:
•The tone control function is unavailable for the Source Direct, Pure Direct, Dolby Headphone, Dolby Virtual Speaker THX mode, and 192kHz PCM.
•The tone control function is not available when PRESET G.EQ is being used.
DIALOGUE NORMALIZATION MESSAGE
Dialogue Normalization (Dial Norm) is a feature of Dolby Digital.
When playing back software which has been encoded in Dolby Digital, sometimes you may see a brief message on the FL display which will read "Dial Norm X dB" (X being a numeric value).
video signal is output from the MONITOR OUT |
terminal. |
(Using the remote control unit)
To adjust the tone, press the AMP button and press the > button PAGE3 is displayed.
Press the NIGHT (D1) button to turn on the Night mode. Setting the Night mode to “ON” compresses the dynamic range in Dolby Digital only.
This softens loud passages such as sudden explosions, to help prevent disturbing others late at night. To turn off the Night mode, Press the NIGHT (D1) button again.
Dialogue Normalization serves to let you know if the source material has been recorded at a higher or lower level than usual. For example, if you see the following message: "Dial Norm + 4 dB" on the FL display, to keep the overall output level constant just turn down the volume control by 4 dB. In other words, the source material that you are listening to has been recorded 4 dB louder than usual.
If you do not see a message on the FL display, then no adjustment of the volume control is necessary.
40