Marantz SR8001, SR7001 manual Hdmi Jack, Connecting Hdmi Devices

HDMI JACK

This SR7001 has four HDMI inputs and one HDMI output (The SR8001 has two HDMI outputs.). It can send digital video and audio signals from DVDs and other sources directly to a display. It minimizes signal degradation caused by analog conversion so that high quality images can be enjoyed.

The SR7001 is also capable of converting analog video signals (Composite Video, S-Video, Component Video) for HDMI output.

• When multiple components are connected to this

receiver, turn power to unused components off to

prevent interference between them.

• Disconnecting or connecting cables with the power

on can damage the equipment. Turn the power off

before disconnecting or connecting cables.

• Some DVD-Audio disks disable downmixing.

These types of disks are not played back correctly

unless the left, center, right and surround left and

right speakers, and subwoofer are connected.

• If a DVD player that does not support HDMI 1.1

DVD player	VIDEO PROJECTOR
HDMI OUTPUT	HDMI INPUT

ENGLISH

Select an input source from the OSD menu system. (See page 25, 36)

Notes:

•When the HDMI output is connected to a display monitor that does not support HDCP, signals are not output. To view images in HDMI, it is necessary to connect to a display that supports HDCP.

•There may be no image output if connected to a TV or display that is not compatible with the above format.

•Refer to the instruction manual of the TV or display to be connected to the SR7001 for detailed information regarding the HDMI terminal.

*HDCP: High-bandwidth Digital Content Protection

is connected to the SR7001, multi channel PCM

playback is not possible even with DVD-Audio

disks.

• If an Super Audio CD player that does not support

HDMI 1.2 is connected to the receiver, DSD

playback is not possible even with Super Audio

CD.

(*DSD: Direct Stream Digital)

• If a DVD player or other device with DVI output

is connected to the SR7001, a separate audio

cable (optical-digital, coaxial digital or analog) is

needed for the audio signals. In this case, select the

connected audio input as explained in “1-1 FUNC

INPUT SETUP”. (See page 25)

• Multi channel PCM signals and audio signals of 62

kHz or higher that are input from the HDMI jack are

not output from the DIGITAL OUT jacks.

INPUT 1(TV)

INPUT 2(DVD)

OUT

SURROUND

MODEL NO. SR8001

BACK

PUT

1

L

RS-232C

FM (75Ω)

GND

AM

ANTENNA

Y

CB/PB

CR/PR

Y

CB/PB

CR/PR

Y

CB/PB

CR/PR

OUT

COMPONENT

PUT

VIDEO

INPUT 3(VCR1)

INPUT 4(DSS/VCR2)

2

R

INPUT 1(TV)

INPUT 2(DVD)

INPUT 3(VCR1) INPUT 4(DSS/VCR2)

OUTPUT 1

OUTPUT 2

HDMI

Ver1.2

L

XM

TV(1)

DVD(2)

VCR1(3)

DSS/VCR2(4) MONITOR MULTI

TV(1)

DVD(2)

VCR1(3)

DSS/VCR2(4)

MONI. OUT

AC IN

OUT

OUT

R

VIDEO

IN

OUT

IN

OUT

IN

OUT

IN

OUT

S-VIDEO

DIGITAL IN

DIGITAL OUT

RC-5 MULTI RC

DC OUT

L

SL

SBL

C

MULTI SPEAKER ON

1

1

/SPEAKER C

OFF

4

5

6

COAX.

IN

SUB SPEAKER

IR

FLASHER RECEIVER

PRE

IN

IN

OUT

UNSWITCHED

2

2

1.25A 150W MAX

1

2

3

OPT.

OUT

EMITTER

R

SR

SBR

SW

OUT

TV

DVD

VCR1

DSS/VCR2

TAPE

CD/CDR

MULTI OUT

L

SL

SBL

C

L

7.1CH

IN

R

SWITCHED

IN

OUT

IN

OUT

IN

OUT

IN

OUT

A

B

R

SR

SBR

SW

1.25A 150W MAX

AC OUTLETS

AUDIO

(AUX2)

120V 60Hz

SPEAKER

SYSTEMS

L

FRONT

A

R

L

FRONT

B

R

CEN

TER

L

SURR.

R

FRONT A OR B.CENTER.SURR. SURR BACK : MINIMUM 6 OHMS FRONT A + B : MINIMUM 8 OHMS

CONNECTING HDMI DEVICES

An HDMI cable (sold separately) is used to connect the HDMI jack on the SR7001 with the HDMI jack on a DVD player, TV, projector or other component. To transmit multichannel audio via HDMI, the connected player must support multichannel audio transmission through its HDMI jack.

HDMI video streaming is compatible with DVI in principle. Therefore, it is possible to connect to a TV or monitor that has a DVI terminal using an HDMI-DVI conversion cable or plug. When connecting to a DVI terminal, connect the audio signal separately.

Notes:

•Some HDMI components can be controlled over the HDMI cable, but this receiver cannot control other components this way.

•When connected to a monitor (i.e., TV, projector, etc.) that does not support HDCP, video and audio are not output.

•DVI cables come with 24-pin and 29-pin plugs. This receiver supports 24-pin DVI-D cables; 29-pin DVI cables cannot connect to it.

•Some source devices such as DVD players or set top box do not support HDMI repeater operations like those of the SR7001. In such case, pictures are not properly projected on monitors such as TVs and projectors.

• Depending on the quiality of the cable used, the

HDMI signal may be affected by noise.

SATELLITE TUNER

HDMI OUTPUT

15