Jonsered GR 2126D manual Emission Control Warranty Statement, Your Warranty Rights And Obligations

Page 28
EMISSION CONTROL WARRANTY STATEMENT

EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND

OBLIGATIONS

The EPA (U.S. Environmental Protection Agency), Environment Canada and Jonsered are pleased to explain the emissions control system warranty on your 2001 and later small off-road engine. In U.S. and Canada, new small off-road engines must be designed, built and equipped to meet the federal stringent antismog standards. Jonsered must warrant the emission control system on your small off-road engine for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your small off-road engine. Your emission control system includes parts such as the carburetor the ignition system and catalytic converter.

Where a warrantable condition exists, Jonsered will repair your small off-road engine at no cost to you including diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COVERAGE

The 2001 and later small off-road engines are warranted for two years. If any emission related part on your engine is defective, the part will be repaired or replaced by Jonsered.

OWNER’S WARRANTY

RESPONSIBILITIES

As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your Owner’s Manual. Jonsered recommends that you retain all receipts covering maintenance on your small off- road engine, but Jonsered cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

As the small off-road engine owner, you should however be aware that Jonsered may deny you warranty coverage if your small off-road engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications. You are responsible for presenting your small off-road engine to a Jonsered authorized servicing dealer as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Jonsered, at Sweden +46 36 14 65 00.

WARRANTY COMMENCEMENT DATE

The warranty period begins on the date small nonroad engine is delivered.

LENGTH OF COVERAGE

Jonsered warrants to the initial owner and each subsequent purchaser that the engine is free from efects in materials and workmanship which cause the failure of a warranted part for a period of two years.

WHAT IS COVERED

REPAIR OR REPLACEMENT OF PARTS

Repair or replacement of any warranted part will be perfor- med at no charge to the owner at an approved Jonsered servicing dealer. If you have any questions regarding your warranty rights and responsibilities, you should ontact your nearest authorized servicing dealer or call Jonsered, at Sweden +46 36 14 65 00.

WARRANTY PERIOD

Any warranted part which is not scheduled for replacement as required maintenance, or which is scheduled only for regular inspection to the effect of ”repair or replace as necessary” shall be warranted for 2 years. Any warranted part which is scheduled for replacement as required maintenance shall be warranted for the period of time up to the first scheduled replacement point for that part.

DIAGNOSIS

The owner shall not be charged for diagnostic labor which leads to the determination that a warranted part is defective, if the diagnostic work is performed at an approved Jonsered servicing dealer.

CONSEQUENTIAL DAMAGES

Jonsered may be liable for damages to other engine components caused by the failure of a warranted part still under warranty.

WHAT IS NOT COVERED

All failures caused by abuse, neglect or improper maintenance are not covered.

ADD -ON OR MODIFIED PARTS

The. use of add-on or modified parts can be grounds for disallowing a warranty claim. Jonsered is not liable to cover failures of warranted parts caused by the use of add-on or modified parts.

HOW TO FILE A CLAIM

If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Jonsered, at Sweden +46 36 14 65 00.

WHERE TO GET WARRANTY SERVICE

Warranty services or repairs shall be provided at all Jonsered authorized servicing dealers.

MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS

Any Jonsered approved replacement part used in the performance of any warranty maintenance or repairs on emission-related parts, will be provided without charge to the owner if the part is under warranty.

EMISSION CONTROL WARRANTY PARTS LIST

1.Carburetor and internal parts

2.Intake pipe, airfilter holder and carburetor bolts.

3.Airfilter and fuelfilter covered up to maintainance schedule.

4.Ignition System

a)Spark Plug, covered up to maintenance schedule

b)Ignition Module

MAINTENANCE STATEMENT

The owner is responsible for the performance of all required maintenance, as defined in the operator’s manual.

28 – English

Image 28
Contents Operator´s manual EPA SYMBOL EXPLANATION SymbolsCONTENTS List of contentsSAFETY INSTRUCTIONS The machine‘s safety equipmentPersonal protective equipment 1. Throttle trigger lock2. Stop switch The stop switch should be used to stop the engine3. Cutting attachment guard 4. Anti-vibration system7. Cutting equipment 6. Muffler8. Locking nut Control, maintenance and service of the machine‘s safety equipment Check that the guard is undamaged and not cracked Reduce the machine‘s tendency to kickback Cutting equipment “Technical data“General safety instructions Fuel safetyStart Transport and storageGeneral working instructions Basic safety precautionsAdjusting the harness and clearing saw Basic clearing techniquesDesignations Grass clearing using a grass blade Brush cutting using the saw bladeClearing‘s ABC Working methodsGrass clearing using the trimmer head and plastic blades ClearingTrimming SweepingWHAT IS WHAT? What is what on the brushcutter?ASSEMBLY Assembly of the blade and trimmer headAssembling the handlebars Assembling the blade guard and grass bladeAssembling the blade guard and clearing blade Assembling the spray guard and trimmer head Tap´n´go ProAdjusting the harness and clearing saw Assembling other guards and cutting equipmentFUEL HANDLING Fuel mixtureFuelling This engine is certified to operate on unleaded gasolineControl before starting START AND STOPStart and stop MAINTENANCE CarburettorRecommended max. speed See “Technical Data” Rec. idling speed 2700 rpmCorrectly adjusted carburettor Final setting of the idling speed THigh speed needle H Cooling system MufflerAngle gear Air filter Spark plugFiling the grass blade 0,5 mmMaintenance schedule Sharpening the clearing bladeDaily maintenance Weekly maintenanceTechnical data TECHNICAL DATAGR2126D EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS6 Nm Poly Trim20mm Trimmy H ´*xre¶5¶¨15 cm 30 - EnglishTap-N-Go Pro “Click”2,0-2,4mm 080-.095108 ´*xre¶5¶¨2002W11