Jonsered GR 2126D manual Safety Instructions, Reduce the machine‘s tendency to kickback

Page 9
•Reduce the machine‘s tendency to kickback

SAFETY INSTRUCTIONS

6. Cutting equipment

This section describes how through correct maintenance and through using the right type of cutting equipment you can:

•Reduce the machine‘s tendency to kickback

•Obtain maximum cutting capacity.

•Increase the service life of the cutting equipment.

Four basic rules:

1)Only use the cutting and guard equipment we recommend! See chapter “Technical data“.

2)Keep the blade‘s teeth well and correctly sharpened! Follow our instructions and use the recommended filing gauge. An incorrectly sharpened or damaged blade increases the risk of an accident.

3)Keep the correct setting. Follow our instructions and use the recommended setting tool. An incorrectly set blade increases the risk of jamming and kickback.

4)Check the cutting equipment with regard to damage and crack formation. Damaged cutting equipment should always be replaced.

7. Quick-release

• Check that the harness straps are correctly positioned. When the harness and machine are adjusted, check the harness‘ safety release catch to ensure it works correctly.

8. Locking nut

• Protect your hand from injury when assembling, use the blade guard as protection when tightening with a socket spanner. Tighten the nut by turning against the direction of rotation. Loosen the nut by turning in the direction of rotation. (NOTE! the nut has a left-hand thread).

•Tighten the nut using a socket spanner, 35 - 50 Nm (3.5 - 5 kpm).

NOTE!

The locking nut‘s nylon lock must not be so worn that it can be turned by hand. The lock shall hold at least 1.5 Nm. The nut should be replaced after it has been put on approx. 10 times.

!WARNING!

Never use a machine with defective safety equipment. The safety equipment should be maintained as described in this section. If your machine does not meet any of these controls you should contact your service workshop.

English – 9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Operator´s manual EPA Symbols SYMBOL EXPLANATIONList of contents CONTENTSThe machine‘s safety equipment SAFETY INSTRUCTIONSPersonal protective equipment 1. Throttle trigger lockThe stop switch should be used to stop the engine 2. Stop switch3. Cutting attachment guard 4. Anti-vibration system6. Muffler 7. Cutting equipment8. Locking nut Control, maintenance and service of the machine‘s safety equipment Check that the guard is undamaged and not cracked Reduce the machine‘s tendency to kickback “Technical data“ Cutting equipmentFuel safety General safety instructionsStart Transport and storageBasic safety precautions General working instructionsBasic clearing techniques Adjusting the harness and clearing sawDesignations Brush cutting using the saw blade Grass clearing using a grass bladeClearing‘s ABC Working methodsClearing Grass clearing using the trimmer head and plastic bladesTrimming SweepingWhat is what on the brushcutter? WHAT IS WHAT?Assembly of the blade and trimmer head ASSEMBLYAssembling the handlebars Assembling the blade guard and grass bladeAssembling the spray guard and trimmer head Tap´n´go Pro Assembling the blade guard and clearing bladeAssembling other guards and cutting equipment Adjusting the harness and clearing sawFuel mixture FUEL HANDLINGFuelling This engine is certified to operate on unleaded gasolineSTART AND STOP Control before startingStart and stop Carburettor MAINTENANCERecommended max. speed See “Technical Data” Rec. idling speed 2700 rpmFinal setting of the idling speed T Correctly adjusted carburettorHigh speed needle H Muffler Cooling systemAngle gear Spark plug Air filterFiling the grass blade 0,5 mmSharpening the clearing blade Maintenance scheduleDaily maintenance Weekly maintenanceTECHNICAL DATA Technical dataGR2126D YOUR WARRANTY RIGHTS AND OBLIGATIONS EMISSION CONTROL WARRANTY STATEMENTPoly Trim 6 Nm20mm ´*xre¶5¶¨ Trimmy H15 cm 30 - English“Click” Tap-N-Go Pro2,0-2,4mm 080-.095´*xre¶5¶¨ 1082002W11
Top Page Image Contents