Jonsered GR 2126D manual Safety Instructions, Stop switch, Cutting attachment guard, Quick-release

Page 5
2. Stop switch

SAFETY INSTRUCTIONS

2. Stop switch

The stop switch should be used to stop the engine.

3.Cutting attachment guard

This guard is intended to prevent objects from being thrown towards the operator and to protect the operator from unintentionel contact with the cutting attachment.

!WARNING!

Do not attach any blade to the unit without proper installation of all required parts. Failure to use the proper parts can cause the blade to fly off and seriously injure the operator and/or bystanders.

Under no circumstances may the cutting equipment be used without an approved guard fitted. See the chapter “Technical data”. If the wrong guard or a defective guard is fitted this can cause serious personal injury.

4.Anti-vibration system

Your machine is equipped with an anti-vibration system that has been designed to give as vibration-free and comfortable usage as possible.

The use of incorrectly wound cord or blunt, incorrect cutting equipment (incorrect type or incorrectly sharpened, see section “Filing the blade”) increases the level of vibration.

The machine’s vibration damping system reduces the transfer of vibrations between the engine unit/ cutting equipment and the machine’s handle unit.

!WARNING!

Over exposure to vibrations can result in blood-vessel or nerve injury to persons suffering with blood circulation problems. Seek medical attention if you experience physical symptoms that can be related to over exposure to vibrations. Examples of such symptoms are “numbness“, lack of feeling, “tickling“, “pricking“, “pain“, lack of or a reduction in normal strength, changes in the colour of the skin or its surfaces. These symptoms normally appear in the fingers, hands or wrists.

5.Quick-release

There is an easily accessible, quick-release catch fitted to the chest as a safety precaution in the event of a fire in the engine or for any other situation that requires you to free yourself from the machine and harness. See the section “Adjusting the harness and clearing saw“.

English – 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Operator´s manual EPA Symbols SYMBOL EXPLANATIONList of contents CONTENTSThe machine‘s safety equipment SAFETY INSTRUCTIONSPersonal protective equipment 1. Throttle trigger lockThe stop switch should be used to stop the engine 2. Stop switch3. Cutting attachment guard 4. Anti-vibration system8. Locking nut 6. Muffler7. Cutting equipment Control, maintenance and service of the machine‘s safety equipment Check that the guard is undamaged and not cracked Reduce the machine‘s tendency to kickback “Technical data“ Cutting equipmentFuel safety General safety instructionsStart Transport and storageBasic safety precautions General working instructionsDesignations Basic clearing techniquesAdjusting the harness and clearing saw Brush cutting using the saw blade Grass clearing using a grass bladeClearing‘s ABC Working methodsClearing Grass clearing using the trimmer head and plastic bladesTrimming SweepingWhat is what on the brushcutter? WHAT IS WHAT?Assembly of the blade and trimmer head ASSEMBLYAssembling the handlebars Assembling the blade guard and grass bladeAssembling the spray guard and trimmer head Tap´n´go Pro Assembling the blade guard and clearing bladeAssembling other guards and cutting equipment Adjusting the harness and clearing sawFuel mixture FUEL HANDLINGFuelling This engine is certified to operate on unleaded gasolineStart and stop START AND STOPControl before starting Carburettor MAINTENANCERecommended max. speed See “Technical Data” Rec. idling speed 2700 rpmHigh speed needle H Final setting of the idling speed TCorrectly adjusted carburettor Angle gear MufflerCooling system Spark plug Air filterFiling the grass blade 0,5 mmSharpening the clearing blade Maintenance scheduleDaily maintenance Weekly maintenanceGR2126D TECHNICAL DATATechnical data YOUR WARRANTY RIGHTS AND OBLIGATIONS EMISSION CONTROL WARRANTY STATEMENT20mm Poly Trim6 Nm ´*xre¶5¶¨ Trimmy H15 cm 30 - English“Click” Tap-N-Go Pro2,0-2,4mm 080-.0952002W11 ´*xre¶5¶¨108
Top Page Image Contents