Jonsered GR 2032D, GR 2026D, GR 2036 manual Final setting of the idling speed T

Page 25

MAINTENANCE

Final setting of the idling speed T

Adjust the idling speed with the screw T, If it is necessary to readjust. First turn the idle speed adjusting screw T clockwise until the cutting attachment starts to rotate/ move. Then turn, counter- clockwise until the cutting attachment stops. A correctly adjusted idle speed setting occurs when the engine runs smoothly in every position. It should also be good margin to the rpm when the cutting attachment starts to rotate/move.

CAUTION! Contact your servicing dealer, if the idle speed setting cannot be adjusted so that the cutting attachment stops. Do not use the machine until it has been properly adjusted or repaired.

High speed needle H

Correctly adjusted carburetor

A correctly adjusted carburetor means that the machine accelerates without hesitation and the machine 4-cycles a little at max speed. Furthermore, the cutting attachment must not rotate/move at idling. A too lean adjusted low speed needle L may cause starting difficulties and bad acceleration.

A too lean adjusted high speed needle H gives lower power = less capacity, bad acceleration and/or damage to the engine. A too rich adjustment of the two speed needles L and H gives acceleration problems or too low working speed.

The high speed needle affects the machine’s power, speed, temperature and fuel consumption. A too lean adjustment on the high speed needle H (the high speed needle H is screwed in too much) gives a too high speed resulting in engine damage. Do not allow the engine to run at full speed for more than 10 seconds.

Apply full throttle and turn the high speed needle H slowly anticlockwise until the engine runs unevenly. The high speed needle H is then turned slowly clockwise a little until the engine runs smoothly.

H

Note the engine should be run unloaded when adjusting the high speed needle. Therefore dismantle the cutting equipment, nut, support flange and disc drive before adjusting the high speed needle. The high speed needle is adjusted correctly when the machine ‘splatters’ a little . If the machine smokes heavily at the same time as it ‘splatters’ heavily the adjustment is too rich.

NOTE! For optimum setting of the carburetor, contact a qualified servicing dealer who has a revolution counter at his disposal.

English – 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents EPA Operator´s manualSymbols Symbol ExplanationContents Machine‘s safety equipment Safety InstructionsPersonal protective equipment Throttle trigger lockCutting attachment guard Stop switchAnti-vibration system Quick-releaseCutting equipment MufflerLocking nut Throttle trigger lock Vibration damping system Cutting equipment Sharpening the clearing blade Cutting equipmentSharpening the grass blade Trimmer headStart Fuel safety General safety instructionsTransport and storage 10 ftGeneral working instructions Basic safety precautionsBasic clearing techniques Adjusting the harness and clearing sawDesignations Clearing‘s ABC Forestry clearing using a saw bladeWorking methods Brush cutting using a grass blade Brush cutting using the saw bladeClearing Grass clearing using the trimmer head and plastic knifesTrimming SweepingWhat is what on the brushcutter? What is WHAT?Assembling the handlebars GR2036 AssemblyTransport position, handlebars Axle is locked Assembling the blade guard and grass bladeAssembling other guards and cutting equipment Adjusting the harness and clearing saw Fuel mixture Fuel HandlingFuelling Control before starting Start and StopStart and stop Carburetor MaintenanceHigh speed needle H Correctly adjusted carburetor Final setting of the idling speed TCooling system MufflerAngle gear Air filter Spark plugFiling the grass blade Daily maintenance Maintenance scheduleWeekly maintenance Monthly maintenanceTechnical data Technical DataGR 2026D GR 2032D Approved accessories GR2036 Type Cutting attachment Approved accessories GR2032D Type Cutting attachmentType Cutting attachment Guard Art No Guard Ref NoYour Warranty Rights Obligations Emission Control Warranty StatementAuto Poly Trim Click Trimmy H Trimmy SII ~ 15 cm ´*xt=¶5Q¨ Page 2002W04 108 88
Top Page Image Contents